RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: ahile
Showing results 1 to 17 of 17
Search took 0.33 seconds.
Forum: Events, Shows and Fun Flys - Airplanes
12-29-2013, 05:44 PM
Replies: 0
Views: 292
Posted By ahile

Northeast Ohio, Multi Club Swapmeet and Auction

February 8, 2014. 10:00AM to 2:00PM
Wooster, Ohio

http://www.rcuniverse.com/forum/attachment.php?attachmentid=1952391http://www.rcuniverse.com/forum/attachment.php?attachmentid=1952392
Forum: E-Flite Helicopters
08-08-2008, 09:54 PM
Replies: 362
Views: 101,755
Posted By ahile

RE: Blade 400 - Tips, tricks, and mods

Check out this website: www.repairblade400.com. Very helpful in replacing the tailboom and belt along with all the other usual repairs.
Forum: Helimax
05-31-2008, 04:35 PM
Replies: 75
Views: 13,680
Posted By ahile

RE: Axe CP going brushless

Mikezell:
I installed the Esky setup (motor and esc) using the 13 tooth pinion from Helidirect. The pinion doesn't seem to mesh with the stock main gear very well. Is this normal? Do I need to...
Forum: Helimax
05-26-2008, 09:13 PM
Replies: 75
Views: 13,680
Posted By ahile

RE: Axe CP going brushless

Need help!!!!! I am trying to install the ESKY EK5-0080 motor and esc combo. I plugged the connector into the receiver, turned on the radio, plugged the battery into the esc and nothing happens. ...
Forum: Helimax
05-13-2008, 05:52 AM
Replies: 75
Views: 13,680
Posted By ahile

RE: Axe CP going brushless

So the ESKY esc can power the receiver then, correct.
Forum: Helimax
05-12-2008, 09:41 PM
Replies: 75
Views: 13,680
Posted By ahile

RE: Axe CP going brushless

pilotlight: I have seen on ebay someone has an HDX BL motor like what you are looking at, with a 2.3mm shaft along with the Hobbywing 18A esc. Would that work also?
Forum: Helimax
05-12-2008, 09:38 PM
Replies: 75
Views: 13,680
Posted By ahile

RE: Axe CP going brushless

mikezell: What all did you have to buy for the BL upgrade? Can the stock motor pinion be used?

I have done the GY240 and esc upgrade for the tail already. I just smoked the 3-in-1 over the...
Forum: Helimax
04-09-2008, 09:12 PM
Replies: 33
Views: 3,617
Posted By ahile

RE: Axe cp gy240 problems

Are you sure the tail motor isn't burnt out. As soon as I installed the gyro and the ESC, my original tail motor burnt out. I replaced it with a GWS motor and have not had any problems since. You...
Forum: Helimax
04-08-2008, 10:35 PM
Replies: 33
Views: 3,617
Posted By ahile

RE: Axe cp gy240 problems

I installed the GY240 gyro and the Electrifly 12amp ESC in accordance with Heli-max installation instructions, exactly. The helicopter flies perfectly. No problems at all. Check all of the wiring...
Forum: Helimax
02-22-2008, 10:58 PM
Replies: 11
Views: 5,492
Posted By ahile

RE: Axe CP and GY240

I just installed the GY240 gyro and the Electrifly C-12 ESC this evening and am really impressed. It improved tail control greatly and I didn't have to fly the tail hardly at all. It will take a...
Forum: Helimax
02-17-2008, 08:08 PM
Replies: 1,960
Views: 198,084
Posted By ahile

RE: axe cp thread

I am working through installing some upgrades. I have the HS-55's installed and am working on wringing out the rigging. I found using the horns that came with the HS-55's don't line up in the center...
Forum: Helimax
02-16-2008, 08:12 AM
Replies: 4
Views: 493
Posted By ahile

RE: AXE CP collective not working. help!

blades on correctly?
Forum: Helimax
02-14-2008, 10:34 PM
Replies: 7
Views: 1,165
Posted By ahile

RE: HELIMAX AXE CP ''NEED HELP''

From what perspective are you flying the helicopter. I stand behind the machine looking at the tail. Basically, viewing it from a pilots perspective. When I throttle up, the nose tends to rotate...
Forum: Helimax
02-05-2008, 12:03 AM
Replies: 13
Views: 1,357
Posted By ahile

RE: Using the HH Gyro on the AXE CP

Has anybody had any experience with the Skyartec gyro and esc from Freestyle Hobby?
Forum: Helimax
01-29-2008, 08:24 PM
Replies: 13
Views: 1,357
Posted By ahile

RE: Using the HH Gyro on the AXE CP

Is the stock transmitter still able to be used or is a better transmitter needed to add, say, the GY240? I'm thinking about adding a gyro in the future, figure then I'll have one for another machine
Forum: Helimax
01-28-2008, 07:24 PM
Replies: 33
Views: 3,010
Posted By ahile

RE: AXE CP Drifts Left

Perhaps tonight I'll try moving the weights further inboard.
Forum: Helimax
01-27-2008, 11:02 PM
Replies: 33
Views: 3,010
Posted By ahile

RE: AXE CP Drifts Left

I too got an Axe Cp two months ago. I have replaced quite a few parts including tail rotor, main rotors, and a few other head parts. I have installed a Blade CP tail rotor, Blade CP flybar paddles...
Showing results 1 to 17 of 17


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.