RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Lancair-RCU
Showing results 1 to 11 of 11
Search took 0.12 seconds.
Forum: YS Engines Support
09-01-2004, 05:44 PM
Replies: 18
Views: 1,606
Posted By Lancair-RCU

RE: YS63 FZ question

Thanks Dave,
That is exactly the answer I was looking for.
I didnt want to have to post it over there just to find that out though, thats why I sent an email to them.
Ill try to find someone...
Forum: YS Engines Support
09-01-2004, 04:13 AM
Replies: 18
Views: 1,606
Posted By Lancair-RCU

RE: YS63 FZ question

It runs better but still not up to spec by a long shot.

I sent an email to the service dept at YSperformance last week asking about pricing for servicing a non warranty engine and have not yet...
Forum: YS Engines Support
08-26-2004, 07:42 AM
Replies: 18
Views: 1,606
Posted By Lancair-RCU

RE: YS63 FZ question

Im embarased to say this.
Being an ex PC tech Im used to taking down notes of the way things come apart to ensure they go back together the same way. However in my haste last night when I changed...
Forum: YS Engines Support
08-25-2004, 09:30 PM
Replies: 18
Views: 1,606
Posted By Lancair-RCU

RE: YS63 FZ question

Duh . . thanks Dave . . . . . . . . . I think.

I hadnt thought of reading the instructions :eek:

Now why did I bother to post all my findings here hoping the YS expert would be able to...
Forum: YS Engines Support
08-24-2004, 11:22 PM
Replies: 18
Views: 1,606
Posted By Lancair-RCU

RE: YS63 FZ question

up
Forum: YS Engines Support
08-24-2004, 08:21 AM
Replies: 18
Views: 1,606
Posted By Lancair-RCU

RE: YS63 FZ question

ARGHHH, after 5 tanks of fuel today, not one iota of change in the compression, its very low hot or cold. On aplus side I did find a peak of 10700rpm and then backed it off to 10300rpm and flew it....
Forum: YS Engines Support
08-23-2004, 04:39 AM
Replies: 18
Views: 1,606
Posted By Lancair-RCU

RE: YS63 FZ question

Just an update, I noticed your "away" message and decided to go ahead and replace the ring.
I broke the old one getting it off but got the new one on without breakage. The old ring was shiny all...
Forum: YS Engines Support
08-22-2004, 02:44 AM
Replies: 18
Views: 1,606
Posted By Lancair-RCU

RE: YS63 FZ question

I competed in my first pattern comp this weekend. 1st in Sportsman (Aussie starting category) but only 2 competitors in the grade so no great big acheivment. Just after a flight, whilst the engine is...
Forum: YS Engines Support
08-15-2004, 03:19 AM
Replies: 18
Views: 1,606
Posted By Lancair-RCU

RE: YS63 FZ question

Well its flown and goes good. I think I ran it too lean on the first flight because when starting it for the 2nd flight I reset the high speed needle and ended up about a 1/4 turn rich from where it...
Forum: YS Engines Support
08-04-2004, 12:43 AM
Replies: 18
Views: 1,606
Posted By Lancair-RCU

RE: YS63 FZ question

OK got the adjuster fixed and set clearances to .003"
Following your suggestions that the idle and reg were possibly too lean I richened them both by 1/8 of a turn. Fired up and let idle fast for 1...
Forum: YS Engines Support
07-30-2004, 06:01 PM
Replies: 18
Views: 1,606
Posted By Lancair-RCU

YS63 FZ question

Hi,
I bought this engine 2nd hand and was "told" it had less than 15 tanks through it. Yesterday I started it for the first time, started easily and idled fast at about 3500 for a minute or so then...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.