RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Straick
Showing results 1 to 15 of 15
Search took 0.04 seconds.
Forum: RC Nitro Stadium Trucks
12-22-2009, 04:47 PM
Replies: 21,657
Views: 1,512,581
Posted By Straick

RE: Official HPI MT2 Thread

My winter project is keeping my revo running in the snow, preferably without getting stuck in the process. Somehow, I don't suffer from cold weather issues of brittle parts yet, but there's always a...
Forum: RC Nitro Stadium Trucks
12-13-2009, 02:13 PM
Replies: 21,657
Views: 1,512,581
Posted By Straick

RE: Official HPI MT2 Thread

I was wondering if there was one available with that style of look for the STOCK MT2. The post you reffered to is good, but unfortunately is achieved by modifying the truck. The main reason I want to...
Forum: RC Nitro Stadium Trucks
12-12-2009, 08:37 PM
Replies: 21,657
Views: 1,512,581
Posted By Straick

RE: Official HPI MT2 Thread

Body question for you all. Is there a body available that will make the MT2 look similar to the Slash(body goes all the way out to the wheels). Only reason I'm asking instead of just going out and...
Forum: RC Nitro Stadium Trucks
11-30-2009, 06:37 PM
Replies: 21,657
Views: 1,512,581
Posted By Straick

RE: Official HPI MT2 Thread

The Trinity is on my Revo. The pipe on my MT2 is the aluminum one, that I think is stock.
I thought of a buku pipe, but can't quite foot the bill for it(if I could, there would be one on my revo...
Forum: RC Nitro Stadium Trucks
11-30-2009, 06:30 PM
Replies: 21,657
Views: 1,512,581
Posted By Straick

RE: Official HPI MT2 Thread

Any suggestions on a pipe that will perform best in low to mid range RPM of the HPI G3.0? The pipe that mine has right now seems to be more of a high end pipe, and I unfortunately spend most of my...
Forum: RC Nitro Stadium Trucks
11-29-2009, 10:46 PM
Replies: 21,657
Views: 1,512,581
Posted By Straick

RE: Official HPI MT2 Thread

It's the HPI G3.0. Sorry I forgot to mention that.
Forum: RC Nitro Stadium Trucks
11-29-2009, 10:36 PM
Replies: 21,657
Views: 1,512,581
Posted By Straick

RE: Official HPI MT2 Thread

Got my rebult motor broke in, and it's running good now. Only have one thing I want to do now. Wondering what type of pipe you all would recommend for low to mid RPM operation(where I end up running...
Forum: RC Nitro Stadium Trucks
11-09-2009, 09:42 PM
Replies: 21,657
Views: 1,512,581
Posted By Straick

RE: Official HPI MT2 Thread

I love the way insert in the front bumper is shaped. Just added 4 leds, setup to run from a 6 volt receiver pack(good use for one that the connector went bad on). I'll post a pic as soon as I get my...
Forum: RC Nitro Stadium Trucks
11-06-2009, 06:26 AM
Replies: 21,657
Views: 1,512,581
Posted By Straick

RE: Official HPI MT2 Thread

Took it apart last night. It WILL need a new piston and sleeve. The current ones look like sand got in there. Didn't find damage anywhere else(thankfully). The worst of the scratches are "I can't...
Forum: RC Nitro Stadium Trucks
11-05-2009, 08:41 PM
Replies: 21,657
Views: 1,512,581
Posted By Straick

RE: Official HPI MT2 Thread

The fiber one with the stamped metal plates.
Ran into a weird problem though. The motor has lots of pinch when cold, but once warm acts as though it's worn out. Won't hold a tune and wants to be...
Forum: RC Nitro Stadium Trucks
11-04-2009, 08:19 PM
Replies: 21,657
Views: 1,512,581
Posted By Straick

RE: Official HPI MT2 Thread

The funny thing is that the setup shown is very similar to what I run on my Revo. Did it there to get rid of the stock TRS, which was slowly trashing servos. I was already planning a setup similar to...
Forum: RC Nitro Stadium Trucks
11-02-2009, 06:42 PM
Replies: 21,657
Views: 1,512,581
Posted By Straick

RE: Official HPI MT2 Thread

Fired up my HPI today, and it simply flew. Still having what I like to call the "new engine blues" at startup, but it runs awesome once warm. Only noticed 2 problems. The first is that the pipe seems...
Forum: RC Nitro Stadium Trucks
10-31-2009, 11:35 PM
Replies: 21,657
Views: 1,512,581
Posted By Straick

RE: Official HPI MT2 Thread

I might be able to save a lot on ebay, but I'll go to my LHS first and keep the money nice and local. Thanks for the suggestion.
Forum: RC Nitro Stadium Trucks
10-31-2009, 11:20 PM
Replies: 21,657
Views: 1,512,581
Posted By Straick

RE: Official HPI MT2 Thread

Will the buku mount to the standard style of header(the one with the 2 screws that hold it on the engine) using the silicone connector? I've seen a bucu pipe in use, and I want one for my Revo and...
Forum: RC Nitro Stadium Trucks
10-31-2009, 10:34 PM
Replies: 21,657
Views: 1,512,581
Posted By Straick

RE: Official HPI MT2 Thread

I have a quick question for you all. I just got a Nitro MT2 G3.0 and am wondering if there are other pipes available for it? Also, is the OS18cvrx a drop in, or do you need a different mount? Thanks....
Showing results 1 to 15 of 15


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.