RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: ws6_man
Showing results 1 to 10 of 10
Search took 0.23 seconds.
05-21-2010, 09:54 PM
Replies: 5
Views: 851
Posted By ws6_man

RE: Clutch bell components

The image posted is not for a avalanche..I found this one, but can't attach it.
ping me and I can email it to you and you might be able to insert it.
05-21-2010, 09:35 PM
Replies: 3
Views: 648
Posted By ws6_man

RE: Lost screw for Avalanche Clutch bell???

The allen head size is 2.5mm
3mm diameter
18mm lenght (thread lenght, not including the allen head).
M3x18...
05-21-2010, 09:27 PM
Replies: 11
Views: 1,149
Posted By ws6_man

RE: does the avalanche clutch bell have bearings on it????

forgot one thing, one more spacer (bare aluminum).
05-21-2010, 09:23 PM
Replies: 11
Views: 1,149
Posted By ws6_man

RE: does the avalanche clutch bell have bearings on it????

I actually had ordered two kits, so I have an unopened one. Here's what ca get:
flywheel collet
flywheel
3 clutch shoes w/ spring
flywheel nut
clutch bell
2 bearings
3 small washers (spacers...
05-21-2010, 09:13 PM
Replies: 11
Views: 1,149
Posted By ws6_man

RE: does the avalanche clutch bell have bearings on it????

Swingline, order this kit from redcat <span id="itmmID">83003
http://www.redcatracing.com/83003.
You have to remove the engine, then unscew the allen screw at the end of the clutch bell. Carefully...
05-21-2010, 08:46 PM
Replies: 299
Views: 40,811
Posted By ws6_man

RE:

I have an Avalanche and about 3/4 gallon, the truck at idle wanted to start moving as before it didn't. Took out engine and dis-assembled clutch bell and found that a clutch shoe broke (not the...
05-21-2010, 03:29 PM
Replies: 4
Views: 570
Posted By ws6_man

RE: Avalanche Brakes

make sure the fiber discs aren't rounded (where the come out of the center diff (transmission)). They are keyed to the output drive cup.
http://www.redcatracing.com/81028...
03-12-2010, 09:17 PM
Replies: 1
Views: 564
Posted By ws6_man

Redcat Avalanche XP engine temps

Just wondering what engine temps ya'll are running at.

ws6_man
Forum: CEN Racing
01-04-2010, 09:41 PM
Replies: 1
Views: 1,623
Posted By ws6_man

CEN GSR 5.0

Does anyone know the o-ring size for the carb body to engine block, there are two orings (upper and lower). Please specify sizes as 10mm ID and 2mm CS (cross section). The carb body measures 14mm w/...
11-11-2009, 01:39 PM
Replies: 2
Views: 2,437
Posted By ws6_man

RE: SH M28-P3 Hi and Low Speed Needle value

http://www.shengines.com/TECHDATA_PT2802B-P3.htm

I think it should start and run (rich) w/ 3 turns from screwed in on both needles.
Showing results 1 to 10 of 10


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.