RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: highflyerbill
Showing results 1 to 11 of 11
Search took 0.22 seconds.
Forum: Speed - Electric
01-23-2013, 07:13 AM
Replies: 8
Views: 947
Posted By highflyerbill

RE: equipment- lost or ?????

Enter a complant with PP they will contact the seller . Check out what PP can do for you on there site .
Forum: Speed - Electric
07-20-2012, 05:41 AM
Replies: 11
Views: 957
Posted By highflyerbill

RE: tunnel hull turning

Are you using a push pull system on the servo to outboard . I would use at least two 4/40 rods, anything else on a tunnel is just not good enough . Also you could try one of the octura M series props...
Forum: Speed - Electric
07-28-2011, 05:07 AM
Replies: 7
Views: 892
Posted By highflyerbill

RE: ESC issues caused by bec/servo need help!

When you used a separate batt. pack did you disconnect the red wire on the ESC to reciever plug if you didnot it will go crazy .
Forum: Speed - Electric
06-28-2011, 05:24 AM
Replies: 390
Views: 76,510
Posted By highflyerbill

RE: Miss Geico 29 Catamaran

Would like a little advise . I have the Geico with a seeking 60 amp ESC X642 prop and www.aircapitolhobbies.com (http://www.aircapitolhobbies.com) off set rudder . Everything else is stock . If I run...
Forum: Glow Engines
06-20-2011, 04:10 PM
Replies: 47
Views: 10,699
Posted By highflyerbill

RE: How much nitro will a 2 stroke take?

I've been out of racing boats for a number of years.When I was racing you eather ran at least 60% Nitro or you stayed home.I did not like to go much above 60% because I liked running caster oil and...
Forum: Airtronics Support Forum
02-01-2011, 06:23 AM
Replies: 2
Views: 760
Posted By highflyerbill

RE: MX-3

Thank you very much.You'rs is a much needed service.
Forum: Airtronics Support Forum
01-29-2011, 03:19 PM
Replies: 2
Views: 760
Posted By highflyerbill

MX-3

I need the manual for the MX-3 75mhz FM 3 ch. radio . If anyone can point me to it I thank you so much.
Forum: Airtronics Support Forum
01-28-2011, 11:09 AM
Replies: 3
Views: 737
Posted By highflyerbill

RE: 2 or 3 ch. FM recievers

It's on 75mhz, I believe airtronics uses pos. shift , so any pos. shift receiver should work.Also JR should work,and I would think there are recievers out there that will work with pos or neg. shift...
Forum: Airtronics Support Forum
01-28-2011, 11:00 AM
Replies: 3
Views: 737
Posted By highflyerbill

RE: 2 or 3 ch. FM recievers

It's on
Forum: Airtronics Support Forum
01-27-2011, 06:56 AM
Replies: 3
Views: 737
Posted By highflyerbill

2 or 3 ch. FM recievers

I have a MX-3 FM transmitter and I need a two or three ch. reciever for.Does anyone out there know what brands will work besides the three ch. asirtronics reciever , which I've been looking for used...
Forum: Electric Aerobatic & Sport Planes
05-11-2010, 10:12 AM
Replies: 2
Views: 930
Posted By highflyerbill

RE: Great Planes SS Brushless Suggestions Please?ng to

The super sportster is a real nice flying plane with a 400 to 450 watt motor . If I were buying it I would go with a Turnigy TR 35-36c 1100 or theSK 35-42 1000 hope that helps a little.
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.