RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: Redcat-Derek
Showing results 1 to 25 of 32
Search took 0.20 seconds.
08-29-2012, 09:00 AM
Replies: 11
Views: 1,470
Posted By Redcat-Derek

RE: Installation of new C-carriers, Drive cups

The screw itself will turn with the tires as it is threaded into the hub so that is good. But if the screw keeps backing itself out most likely the hub's threads are worn causing the screw to not be...
08-29-2012, 08:49 AM
Replies: 3
Views: 844
Posted By Redcat-Derek

RE: EQ8e part number

The link is part number BS903-008, and the longer screw that goes through the carrier is part number 60075.
08-29-2012, 08:37 AM
Replies: 2
Views: 833
Posted By Redcat-Derek

RE: New parts dont fit old Tornado.

Exactly, the newer one way bearing part number that you need is 06267.
08-29-2012, 08:32 AM
Replies: 1
Views: 783
Posted By Redcat-Derek

RE: Help Identifying a Volcano S30 Part

The correct one you need is part number 02025. You have pictured the servo saver that has the 2 arms coming off, the other side just has the one arm.<br type="_moz"/>
02-14-2011, 10:01 AM
Replies: 8
Views: 2,491
Posted By Redcat-Derek

RE: motor turns?

Hey rsw007,

Go ahead and shoot me and email to [email protected] and I will see what I can do for you.

Thanks,
Derek
RedcatRacing
09-13-2010, 01:56 PM
Replies: 2
Views: 18,902
Posted By Redcat-Derek

RE: SH .18 Factory Needle Settings?

Hello VS30,

Factory settings on the sh.18 engine are going to be 2.5-3 turns out from fully closed on the high and low speed needles. And the idle screw doesn't have a factory setting, just make...
08-30-2010, 04:35 PM
Replies: 11
Views: 1,484
Posted By Redcat-Derek

RE: Electronics protection

cswtornado,

You could try connecting one end of the spring to the throttle linkage, and the other end to like the shock tower. Something like that should work.

Thanks,
Derek
RedcatRacing
08-30-2010, 04:32 PM
Replies: 50
Views: 51,683
Posted By Redcat-Derek

RE: Diff fluids Just the basics

Hello formula87,

The diffs should come filled with grease, so i would recommend putting some silicone diff fluid in them to tune per your preference.

Thanks,
Derek
RedcatRacing
08-24-2010, 11:56 AM
Replies: 11
Views: 1,484
Posted By Redcat-Derek

RE: Electronics protection

cswtornado,

Well if you are losing power completely them it's most likely going to be a bad connection somewhere causing the receiver to get no power. I would even get another battery holder and...
08-24-2010, 11:06 AM
Replies: 50
Views: 51,683
Posted By Redcat-Derek

RE: Diff fluids Just the basics

zanga254,

I would recommend at least putting some grease in the diff to keep it lubed. Without some type of lubricant the gears are going to wear faster than normal.

Thanks,
Derek...
08-24-2010, 10:56 AM
Replies: 11
Views: 1,484
Posted By Redcat-Derek

RE: Electronics protection

cswtornado,

If the power was cut off then nothing would work on the vehicle and you could turn the servos by hand, meaning the on/off switch could broke or you lost a connection. But if you still...
08-20-2010, 11:11 AM
Replies: 11
Views: 1,484
Posted By Redcat-Derek

RE: Electronics protection

cswtornado,

It could be the receiver or the battery holder, when jarred does the electronics completely shut off with no power?

Thanks,
Derek
RedcatRacing
08-16-2010, 04:07 PM
Replies: 3
Views: 901
Posted By Redcat-Derek

RE: Price difference

Revolauncher,

Just to clarify the volcano isn't a clone of the t-maxx. Clone to me is a exact replica like king motors to the hpi baja.

Thanks,
Derek
RedcatRacing<br type="_moz"/>
08-16-2010, 03:56 PM
Replies: 1
Views: 2,632
Posted By Redcat-Derek

RE: Volcano s30 tuning

Bnecaise74,

Its a great vehicle, and I've had great luck with the sh .18. Every engine I've had started within 3 pulls when cold, was easy to tune and held it. I actually had one that ran awesome...
08-02-2010, 12:29 PM
Replies: 12
Views: 2,740
Posted By Redcat-Derek

08-02-2010, 11:26 AM
Replies: 14
Views: 1,785
Posted By Redcat-Derek

RE: Making an 8E rear wheel drive instead of all wheel

Hello,

Having a center differential, you will need to either keep it 4WD or lock the center diff and run RWD which I wouldn't recommend. If you just take the front drive shaft out the center diff...
08-02-2010, 11:17 AM
Replies: 1
Views: 717
Posted By Redcat-Derek

RE: could someone please help me with factory settings on sh1.8 carb nitro please

dbink,

Factory setting on a sh .18 carb is going to be 2.5-3 turns out from fully closed on the high and low speed needle.

Thanks,
Derek
RedcatRacing<br type="_moz"/>
07-27-2010, 03:05 PM
Replies: 5
Views: 1,656
Posted By Redcat-Derek

RE: New Monsoon XTR owner

thorMaXx-

I've found the stock shocks with stock weight to be good for bashing, but you can always fine tune them for your liking. The mud gaurds from the hurricane xp will fit the avalanche, but...
07-27-2010, 03:01 PM
Replies: 8
Views: 1,148
Posted By Redcat-Derek

RE: WILL AN OS.21VG (P) ENGINE FIT IN A AVALANCHE

Catbob-

That head is actually to the .21 not the .28. So the .28 will be a bit bigger also. I've had no problems running any engine here in Arizona.

Thanks,
Derek
RedcatRacing<br type="_moz"/>
07-23-2010, 11:05 AM
Replies: 3,672
Views: 316,952
Posted By Redcat-Derek

RE: Redcat Racing Tornado Thread

whauburger,

Try going back to factory settings on your needles. 2.5-3 turns out on the high and low speed needle and then tune from there. It really shouldnt be dieing because all its doing is...
07-21-2010, 01:09 PM
Replies: 23
Views: 3,696
Posted By Redcat-Derek

RE: Earthquake 3.0 Advice

If you guys are having problem with break in or tuning you can always give us a call at (602-454-6445) and even ask for me and I can help you out with your problems. Sometimes its easier to...
07-21-2010, 12:51 PM
Replies: 5
Views: 1,075
Posted By Redcat-Derek

RE: 100 degree weather and nitro

qoisdhc ogina,

Common sense would  tell you that you would need to richen the needles to keep the engine cool, but you actually need to lean the needles when the temperature is hotter. Reason...
07-20-2010, 11:20 AM
Replies: 5
Views: 1,075
Posted By Redcat-Derek

RE: 100 degree weather and nitro

Rokit,

You should be fine running in 100+ degree weather, when going from a colder to hotter temperature you will need to lean the needles to compensate for less density in the air. What probably...
07-19-2010, 01:05 PM
Replies: 8
Views: 1,167
Posted By Redcat-Derek

RE: Adjusting diffs

Rokit,

You can put some thick silicone differential fluid in the diffs which will give it more of a locked feel. That should help to keep it tracking straight.

Thanks,
Derek
RedcatRacing
07-15-2010, 11:55 AM
Replies: 4
Views: 2,906
Posted By Redcat-Derek

RE: Caldera 10E Battery Size (Dimensions)

Jaturner,

The battery tray is 27mm in width, 141mm in length

Thank you,
Derek
RedcatRacing<br type="_moz"/>
Showing results 1 to 25 of 32
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.