RCU Forums - Search Results

Search: Posts Made By: aspeed

Showing results 1 to 7 of 7
Search took 0.02 seconds.

Forum: "1/2 A" & "1/8 A" airplanes

07-02-2014, 03:08 AM

Replies: 227

Cox TD .010 Ply Rolled Fuselage 3Ch Speeder

Views: 19,934

Posted By aspeed

For the Tee Dee .049 backplate pressure, we used...

For the Tee Dee .049 backplate pressure, we used a pressure fitting soldered right up closed, with a piece of wire going through. The wire was waxed or oiled so it could be removed easily. The rule...

Forum: "1/2 A" & "1/8 A" airplanes

05-21-2014, 12:58 PM

Replies: 227

Cox TD .010 Ply Rolled Fuselage 3Ch Speeder

Views: 19,934

Posted By aspeed

I think all of the older CS stuff was spotty. I...

I think all of the older CS stuff was spotty. I have two CS .049s. This one never went as good as a TD until I made a new head after trying two other stock ones. One looked good, it was not a...

Forum: "1/2 A" & "1/8 A" airplanes

05-21-2014, 05:51 AM

Replies: 227

Cox TD .010 Ply Rolled Fuselage 3Ch Speeder

Views: 19,934

Posted By aspeed

Kind of like the Norvel large tank....

Kind of like the Norvel large tank. http://www.nvengines.com/index.php?page=shop.product_details&flypage=flypage.tpl&product_id=69&category_id=3&option=com_virtuemart&Itemid=67 The smaller one was...

Forum: "1/2 A" & "1/8 A" airplanes

05-20-2014, 04:57 AM

Replies: 227

Cox TD .010 Ply Rolled Fuselage 3Ch Speeder

Views: 19,934

Posted By aspeed

The CS .049 I have is totally different. That...

The CS .049 I have is totally different. That one may respond well to a new head, but this one is ABC BB and shares the case with an .06 model. The stock TD doesn't need pressure, just if you open...

Forum: "1/2 A" & "1/8 A" airplanes

05-08-2014, 06:23 AM

Replies: 227

Cox TD .010 Ply Rolled Fuselage 3Ch Speeder

Views: 19,934

Posted By aspeed

You may be ok with a fairly high idle, the little...

You may be ok with a fairly high idle, the little planes pretty much fall out of the air at 6,000 rpm because of the small prop blades. It is nice to be able to shut it off for landing, but at a two...

Forum: "1/2 A" & "1/8 A" airplanes

05-03-2014, 05:39 AM

Replies: 227

Cox TD .010 Ply Rolled Fuselage 3Ch Speeder

Views: 19,934

Posted By aspeed

There was a guy did that with an rc plane many...

There was a guy did that with an rc plane many moons ago. After experimenting, they found that an extra line was needed on the outboard wing to keep it stable. Something to show off with at the fun...

Forum: "1/2 A" & "1/8 A" airplanes

04-18-2014, 08:01 AM

Replies: 227

Cox TD .010 Ply Rolled Fuselage 3Ch Speeder

Views: 19,934

Posted By aspeed

You could just make a piece of tubing with a...

You could just make a piece of tubing with a lathe. It may be hard to find just the right size. I found the sizes vary a bit from nominal with the K&S stuff. You may need to find someone with a...

Showing results 1 to 7 of 7