RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: stealthdragonb
Showing results 1 to 13 of 13
Search took 0.12 seconds.
Forum: Electric General Discussion
09-11-2012, 01:11 AM
Replies: 1
Views: 2,217
Posted By stealthdragonb

RE: Hyperion ZS 4035-12 with ATLAS 90 amp OPTO ESC

I would appreciate anyones helpful advice...
Forum: Electric General Discussion
09-09-2012, 06:52 PM
Replies: 1
Views: 2,217
Posted By stealthdragonb

Hyperion ZS 4035-12 with ATLAS 90 amp OPTO ESC

Hi All I am using a Hyperion ZS 4035-12 motor with a Hyperion Atlas 90 amp OPTO esc with 8S LiPo. Previously I was using a turnigy 100 amp superbrain esc and was achieving a current draw of 60 amps...
Forum: Electric General Discussion
04-30-2012, 04:42 PM
Replies: 10
Views: 1,755
Posted By stealthdragonb

RE: 10kg Flyin King with Hyperion ZS4035-12

okay, I'll try that today. What is the EPA setting on the Tx, I checked the throttle curve and it is linear going from 0% an finally to 100%, is this what you mean?
Forum: Electric General Discussion
04-30-2012, 12:10 AM
Replies: 10
Views: 1,755
Posted By stealthdragonb

RE: 10kg Flyin King with Hyperion ZS4035-12

Hello,
I am using a eagletree power panel which is failry accurate as I have also got the same results using another wattmeter. By the way I think I am close to figuring out the problem. I plugged...
Forum: Electric General Discussion
04-29-2012, 05:38 PM
Replies: 10
Views: 1,755
Posted By stealthdragonb

RE: 10kg Flyin King with Hyperion ZS4035-12

I tried a 17x12 APC prop today and got 28A current draw which is an improvement from before and most likely will increase the amount of current draw as propeller diameter is increased. So obviously...
Forum: Electric General Discussion
04-28-2012, 08:57 PM
Replies: 10
Views: 1,755
Posted By stealthdragonb

RE: 10kg Flyin King with Hyperion ZS4035-12

Thanks for your prompt replies,
Yeah I get similar results using motocalc but when I try and test the actual motor with 8s, the 14x12 given only a current draw of 26A and the 15x10 gives only 15A....
Forum: Batteries & Chargers
03-03-2012, 05:47 PM
Replies: 12
Views: 1,340
Posted By stealthdragonb

RE: Determining AWG of silicon wires (using four, 4 cell 5800mAH LiPo)

The plane being used is a Flyin King fuselage with a custom built wing which is somewhat going to improve lift and reduce drag if calculations are done right.  This plane will be carrying a heavy...
Forum: Batteries & Chargers
03-02-2012, 11:05 PM
Replies: 12
Views: 1,340
Posted By stealthdragonb

RE: Determining AWG of silicon wires (using four, 4 cell 5800mAH LiPo)

Okay, so using 12AWG silicon wires for batteries in parallel shouldn't be any problem. What is the best and most accurate way to determine how much ampage my motor is taking during takeoff, cruise...
Forum: Batteries & Chargers
03-01-2012, 02:50 PM
Replies: 12
Views: 1,340
Posted By stealthdragonb

RE: Determining AWG of silicon wires (using four, 4 cell 5800mAH LiPo)

I agrre with all of you. I did a simple mistake in my earlier post. The plane is most likely going to be set to cruise at approximately 18-20m/s which is going to require 170W of power which gives...
Forum: Batteries & Chargers
02-28-2012, 10:38 PM
Replies: 12
Views: 1,340
Posted By stealthdragonb

RE: Determining AWG of silicon wires (using four, 4 cell 5800mAH LiPo)

Motor pulls approximately 70 amps and ESC can handle 100amps.
Forum: Batteries & Chargers
02-28-2012, 10:31 PM
Replies: 12
Views: 1,340
Posted By stealthdragonb

Determining AWG of silicon wires (using four, 4 cell 5800mAH LiPo)

Hello,
I have got four 5800mAH LiPo batteries with a discharge of 25-35C which are all identical and are four cell Lipo's. I have created 2 series adapters with dean connections. I am connecting two...
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.