RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: AWorrest
Showing results 1 to 25 of 500
Search took 0.80 seconds.
09-16-2023, 02:20 PM
Replies: 3
Views: 527
Posted By AWorrest

In the ACRO programming configuration, the XG14...

In the ACRO programming configuration, the XG14 supports only one user-defined throttle curve. It is turned ON and OFF by the condition(s) set in the SW SEL submenu on page 2 of the THRO CURVE menu....
06-11-2023, 03:43 PM
Replies: 3
Views: 581
Posted By AWorrest

It’s been a while since I’ve used my 9303...

It’s been a while since I’ve used my 9303 (practically the same as the 9503). Last night I took a look at it and I should add these comments. First, when the FLAPERON wing type is chosen, the left...
06-10-2023, 04:07 PM
Replies: 3
Views: 581
Posted By AWorrest

If I am in correctly reading your question, you...

If I am in correctly reading your question, you are using AUX2 as your left aileron through a program mix. If true, you are programming your transmitter in a manner it was not designed to handle....
05-14-2023, 04:45 PM
Replies: 10
Views: 1,120
Posted By AWorrest

As the transmitter issues a warning when switched...

As the transmitter issues a warning when switched on and when the flight mode switch is not in the NORM position, you could use that switch position for the throttle kill instead of the HOLD...
05-11-2023, 01:56 PM
Replies: 10
Views: 1,120
Posted By AWorrest

I will have to take a look at my 9303 to confirm...

I will have to take a look at my 9303 to confirm what I’m about to write, but I don’t believe that there is any menu on the 9303/9503 that allows you to set the warnings. The warnings that these...
03-10-2023, 06:11 PM
Replies: 5
Views: 1,247
Posted By AWorrest

Peter, Glad to read that it worked out....

Peter,

Glad to read that it worked out. Replying to questions such as yours gives me the incentive to dig into the programming deeper than I normally would.

Allan
03-08-2023, 09:10 AM
Replies: 3
Views: 831
Posted By AWorrest

If the timer is set up to approximate fuel...

If the timer is set up to approximate fuel consumption by having the SPS trip point set at mid-stick position, the start/stop beeps can get very annoying. The trouble with using the F button is that...
03-08-2023, 08:57 AM
Replies: 5
Views: 1,247
Posted By AWorrest

Take a look at the Throttle Curve menu. In the...

Take a look at the Throttle Curve menu. In the upper left corner, second line down, there should be a four-character notification such as RTH0. Using the roller/selector, highlight the notification...
03-07-2023, 05:13 PM
Replies: 3
Views: 831
Posted By AWorrest

The start/stop beeps come from the timer; they...

The start/stop beeps come from the timer; they are not a part of the stick position switches setup. If you want the timer to have count down beeps, you have to put up with the start/stop beeps. You...
10-27-2022, 08:24 PM
Replies: 2
Views: 599
Posted By AWorrest

On the XG series and later, you cannot blank-out...

On the XG series and later, you cannot blank-out the model that you are working from. As you found out, the erase function just wipes out what you had and sets it up for a new model. When you erase a...
09-29-2022, 06:08 PM
Replies: 4
Views: 1,160
Posted By AWorrest

Close but not quite, the T14 is similar to the...

Close but not quite, the T14 is similar to the XG14. The programming is the same but it has more expensive gimbals. It is the T44 that is similar to the XG11. I haven’t ever seen a book on...
07-26-2022, 02:42 PM
Replies: 7
Views: 891
Posted By AWorrest

While I have more DMSS receivers than aircraft,...

While I have more DMSS receivers than aircraft, occasionally I get a compulsion to buy another. JR can be tight-lipped in explaining how their designs work. From the little they put out, the 2K seems...
07-23-2022, 08:32 PM
Replies: 7
Views: 891
Posted By AWorrest

It is strange that the JR507 servo didn’t work...

It is strange that the JR507 servo didn’t work with your RG612BX receiver. They work on mine. Have you spoken to DFA/JR about this? Is it possible that your receiver is the 2K version? My RG612BX...
06-12-2022, 08:15 PM
Replies: 7
Views: 1,575
Posted By AWorrest

The XG14/T14 programming is not as sophisticated...

The XG14/T14 programming is not as sophisticated as the XG11/T44. They both have two sets of servo speeds for each of the direction the servo moves. While the XG11 allows you to select the P0 speeds,...
05-14-2022, 06:20 PM
Replies: 2
Views: 736
Posted By AWorrest

See if the throttle channel doesn’t activate your...

See if the throttle channel doesn’t activate your aileron and retract servos. Whenever you reset the XBus, servos or converters, they revert to the throttle channel.
02-12-2022, 05:27 PM
Replies: 3
Views: 1,810
Posted By AWorrest

If your transmitter cannot work with the AR6610T...

If your transmitter cannot work with the AR6610T receiver, it is not due to it having Forward Programming. I had no problem with linking my 12X (module version) transmitter to an AR637T receiver that...
02-12-2022, 03:45 PM
Replies: 2
Views: 1,362
Posted By AWorrest

There is a blurry picture of the Elite on the US...

There is a blurry picture of the Elite on the US distributor website home page banner, https://www.deeforce.net/ How close this is to the actual transmitter is anyone’s guess.

Allan
01-21-2022, 11:14 AM
Replies: 7
Views: 1,575
Posted By AWorrest

The two trims are on the top front center of the...

The two trims are on the top front center of the transmitters. The attached drawing is for the XG14 but it is the same for the T14. Check the Wing Type menu to be certain that the trim you pick for...
01-20-2022, 03:08 PM
Replies: 7
Views: 1,575
Posted By AWorrest

Set up your program mixes to do what you want. ...

Set up your program mixes to do what you want.

Starting with the question of inhibiting nose wheel steering, first be certain the steering channel, AUX8, is disconnected from all inputs. In the...
01-20-2022, 12:22 PM
Replies: 24
Views: 2,801
Posted By AWorrest

I have one of those relatively rare XG11 that is...

I have one of those relatively rare XG11 that is modular. I can use a DSM module but mostly run it as DMSS. You are taking a chance of ruining your DSM JR 11X if you try to install DMSS firmware in...
01-11-2022, 11:02 AM
Replies: 1
Views: 687
Posted By AWorrest

Spektrum made a DSM2 module for JR transmitters,...

Spektrum made a DSM2 module for JR transmitters, https://www.spektrumrc.com/Products/Default.aspx?ProdId=SPMMSJR710. You might find a used unit. I have one and it works.
10-05-2021, 06:49 PM
Replies: 8
Views: 2,144
Posted By AWorrest

In the DX8e manual it states that a AS3X Gain...

In the DX8e manual it states that a AS3X Gain Live View telemetry screen can be set up on your transmitter where you can adjust the gains. Setting up the screen also establishes a gain menu in the...
10-05-2021, 01:16 PM
Replies: 8
Views: 2,144
Posted By AWorrest

If you are using analog servos, I had the same...

If you are using analog servos, I had the same problem with an AR637T. By default the signal the receiver sends to the servo has a 11ms frame rate. This is too fast for some analog servos. This...
09-21-2021, 11:31 AM
Replies: 8
Views: 3,194
Posted By AWorrest

The JR 11X Zero was never sold in the United...

The JR 11X Zero was never sold in the United States. Have you tried contacting the new parent company in Japan at https://www.jrpropo-jp.com/ ? They don’t list your transmitter on their download...
Replies: 2
Views: 2,020
Posted By AWorrest

JR Propo / Dee Force Aviation is selling their...

JR Propo / Dee Force Aviation is selling their last units at $600, https://www.deeforce.net/product-page/xg11mv-dmss-module The XG series is no longer being manufactured, so even new it is one step...
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.