RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: motoxxx996
Showing results 1 to 13 of 13
Search took 0.05 seconds.
Forum: Kit Building
05-06-2011, 09:35 AM
Replies: 31
Views: 26,205
Posted By motoxxx996

RE: Sig 1/6 Cub Build

I am securing them to the "doubled rib" that I built into the wing. I needed to cover it first though. Good looking out though. ;)
Forum: Kit Building
05-04-2011, 08:22 AM
Replies: 31
Views: 26,205
Posted By motoxxx996

RE: Sig 1/6 Cub Build

A small amount of progress has been made, I covered the bottem of the wing and the struts epoxied in place covered.
Forum: Kit Building
09-26-2010, 11:08 PM
Replies: 31
Views: 26,205
Posted By motoxxx996

RE: Sig 1/6 Cub Build

I got the wing struts all hinged and the clevises installed. The servo mounts are in place and the elevator push rods are made. I made hatches for the wing servos too.
Forum: Kit Building
09-21-2010, 08:22 AM
Replies: 31
Views: 26,205
Posted By motoxxx996

RE: Sig 1/6 Cub Build

Ya, I'm going to make mine look like every other Cub out there, I already bought the Solartex Cub yellow covering. I have always liked the way that they look wrapped in yellow so I'm joining the...
Forum: Kit Building
09-20-2010, 10:05 PM
Replies: 31
Views: 26,205
Posted By motoxxx996

RE: Sig 1/6 Cub Build

A little more progress, it should be time to start covering soon.
I sure hope it flys good. I flew a cub arf (I don't know what brand it was) and man did it fly like junk!
Forum: Kit Building
07-13-2010, 09:39 AM
Replies: 31
Views: 26,205
Posted By motoxxx996

RE: Sig 1/6 Cub Build

No progress for a while, I'm trying to get motivated again. I have spent most of my free time working on a couple of heli's and I'm FINALLY switching the fleet over to 2.4ghz so there has been a lot...
Forum: Kit Building
04-09-2010, 11:40 AM
Replies: 31
Views: 26,205
Posted By motoxxx996

RE: Sig 1/6 Cub Build

Making more progress, the cabins bottom is sheeted and the stringers are installed on the rear section of the fuselage including the fin. I also the dowels inplace to hold the stab.
Forum: Kit Building
04-01-2010, 04:52 PM
Replies: 31
Views: 26,205
Posted By motoxxx996

RE: Sig 1/6 Cub Build

Not much progress, got the wing hold down wires in place and the firewall in and the front sheeted.
Forum: Kit Building
03-19-2010, 02:54 PM
Replies: 31
Views: 26,205
Posted By motoxxx996

RE: Sig 1/6 Cub Build

The dreaded spruce cabin is built next up is the front wing hold down wires
Forum: Kit Building
03-17-2010, 11:43 AM
Replies: 31
Views: 26,205
Posted By motoxxx996

RE: Sig 1/6 Cub Build

Thanks for the tip, I would imagine that doubling the spruce with some thin balsa would go unnoticed and add a fair amount of strength when the joints are staggered.
Forum: Kit Building
03-17-2010, 10:44 AM
Replies: 31
Views: 26,205
Posted By motoxxx996

RE: Sig 1/6 Cub Build

The fuselage is all stick built and takes some time. I used a bench sander to get all the angles cut even, it was time consuming but it made all the joints very tight. The instructions on the...
Forum: Kit Building
03-16-2010, 10:58 PM
Replies: 31
Views: 26,205
Posted By motoxxx996

RE: Sig 1/6 Cub Build

The kit is a full wing, but I have a OS Surpass 48 that I want to put in it and that would be way to much motor for it, so I removed two rib sections from each wing. I guess I should have do it...
Forum: Kit Building
03-16-2010, 10:43 PM
Replies: 31
Views: 26,205
Posted By motoxxx996

Sig 1/6 Cub Build

I have started the build on a 1/6 sig Cub build that I got on ebay. It is an old old kit but it is in great shape. All the parts are there so far the building is going well.
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.