RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: wolf152
Showing results 1 to 25 of 43
Search took 0.65 seconds.
Forum: Gas Engines
03-14-2004, 03:36 PM
Replies: 2
Views: 633
Posted By wolf152

RE: Sachs ID help

Thanks Terry.

wolf152
Forum: Gas Engines
03-14-2004, 01:10 PM
Replies: 2
Views: 633
Posted By wolf152

Sachs ID help

Need help ID'ing a Sachs motor. Casting # 44ZN18.

Thanks all,


wolf152
07-27-2003, 10:51 PM
Replies: 0
Views: 444
Posted By wolf152

Wanted:paperwork Dorman P-51 cockpit

Looking for all related paperwork (plans) for Dorman P-51 cockpit kit.

Thanks,

wolf152
Replies: 4
Views: 588
Posted By wolf152

Charging

Try Radical RC. Read the charging new batt. section.

wolf152
Forum: Kit Building
04-20-2003, 10:52 PM
Replies: 3
Views: 918
Posted By wolf152

Shrike Commander

I could be wrong, but I think this is a copy of the Ace Shrike Comm.. More of a collectors item, and may be pricy. The Ace is RCM plan# 640 @ $6. Quantum sells the Ace foam cores for $6.99. You need...
02-18-2003, 12:45 AM
Replies: 58
Views: 6,330
Posted By wolf152

Poulan 42

flipflop,

Are you using the stock carb on these motors?

wolf152
Forum: Glow Engines
02-17-2003, 01:17 AM
Replies: 48
Views: 5,107
Posted By wolf152

bearing replacement

Wrap wire around bearing for ease of removal from pan. Place bearing in pan with enough oil to cover. Heat to 200 degrees. Put on gloves. Remove bearing from oil and slide on shaft quickly. Press...
02-15-2003, 02:40 PM
Replies: 7
Views: 2,279
Posted By wolf152

Kaos

I picked up the 60 size RCM plans and foam cores on E-bay from McClain wing cores. Less than $30 shipped.

wolf152
01-12-2003, 06:59 PM
Replies: 102
Views: 46,714
Posted By wolf152

Carbide end mills

Eric,

www.mscdirect.com

wolf152
01-12-2003, 02:28 PM
Replies: 102
Views: 46,714
Posted By wolf152

Carbide end mills

Try MSC for your small end mills, high helix. If you use the tool offset, you can "climb mill" on a light final pass, say .010, you might not have to sand.

wolf152
12-28-2002, 04:29 PM
Replies: 77
Views: 7,459
Posted By wolf152

Foam cutter

I've got very little voltage on the short setting. Any ideas on what I did wrong?

wolf152
12-26-2002, 11:07 PM
Replies: 1
Views: 434
Posted By wolf152

Viking

Did you try aerodyne online? They have a large selection of oldies.

wolf152
10-20-2002, 09:49 PM
Replies: 2
Views: 859
Posted By wolf152

retracts

Look in the May 2001 issue of MAN. It shows a cutaway drawing of how the pivot block locks the gear in both positions. This is the most important issue to resolve.

wolf152
09-18-2002, 07:21 PM
Replies: 18
Views: 27,267
Posted By wolf152

Hard Coat

You can Hard Coat at your local annodizer. This process leaves a hard shell (.001-.002) on the surface. It is very hard and resistant to scratches, but will chip if hit hard enough.

wolf 152
09-03-2002, 08:07 AM
Replies: 7
Views: 742
Posted By wolf152

Please Help with My Giant Scale Spinner Problem!!!

www.mscdirect.com

There's a store in Orlando. I'll check at work today and see if I have any.
08-23-2002, 11:54 PM
Replies: 7
Views: 1,818
Posted By wolf152

Don Godfrey Super Stearman

Check your mail.

wolf152
08-23-2002, 09:34 PM
Replies: 7
Views: 1,818
Posted By wolf152

Don Godfrey Super Stearman

I think I have the two piece cowl. It's 10 1/2" Dia. ,10" long 1/8 thick.

wolf152
Forum: 3D Flying!
08-20-2002, 08:00 PM
Replies: 9
Views: 2,338
Posted By wolf152

Wanted: Large Ultimate Biplane Plans

Chris,

Sent you some mail.
Forum: Kit Building
07-03-2002, 08:44 PM
Replies: 4
Views: 1,420
Posted By wolf152

Need (2) 6-32 eye bolts

MSC has them. But at $7.54 each I don't think I'd buy them.

MSC Industrial Supply

wolf152
Forum: ARF or RTF
06-23-2002, 01:48 PM
Replies: 5
Views: 807
Posted By wolf152

replacement foam wings needed

Check out G&L Hobbies.

wolf152
06-13-2002, 09:50 PM
Replies: 4
Views: 1,570
Posted By wolf152

Looking for a Mantua Models importer

I believe Model Expo handles their boat line. Maybe they can help.

wolf152
06-13-2002, 09:41 PM
Replies: 3
Views: 597
Posted By wolf152

Materials location

Try Certainly Wood in N.Y. $1.50/Sq.Ft. Excellent Quality.

www.certainlywood.com


wolf152
Forum: Kit Building
06-06-2002, 04:00 PM
Replies: 4
Views: 747
Posted By wolf152

Weeks Solution

Taildragger,

Sent you some mail.

wolf152
05-18-2002, 11:39 AM
Replies: 3
Views: 3,638
Posted By wolf152

Wing Tubes: Where To Buy?

www.tntlandinggear.com
Showing results 1 to 25 of 43
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.