RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: psrumors
Showing results 1 to 25 of 45
Search took 0.64 seconds.
11-25-2012, 03:03 PM
Replies: 1
Views: 725
Posted By psrumors

RE: Futaba 3pl & Opti-drive problems

Never mind...the Futaba doesn't work with the optidrive so I bypassed the Opti. Simple enough.
11-25-2012, 02:33 PM
Replies: 1
Views: 725
Posted By psrumors

Futaba 3pl & Opti-drive problems

Just bought a 3pl, installed the receiver and programmed the Opti drive. After doing so the throttle and brakes work but all I have is reverse. If I move the 3ch switch to the opposite position the...
11-12-2012, 05:01 AM
Replies: 4
Views: 860
Posted By psrumors

RE: Bought a used 5B

Thanks for the info.
11-11-2012, 05:34 PM
Replies: 4
Views: 860
Posted By psrumors

Bought a used 5B

which I think is a v1 RTR. Am I correct?

I have always wanted a 5T but this one showed up at the local pawn shop so I took a chance and made an offer, was surprised when they accepted it....$300...
02-12-2006, 06:31 AM
Replies: 1
Views: 309
Posted By psrumors

RE: Servo ?

It works just fine. I am running a Hitec 5945 with no problems.
02-10-2006, 08:44 AM
Replies: 4
Views: 445
Posted By psrumors

Ballistic Extended Chassis, Who has it and how does it work?

I am wanting an extended chassis, I have seen the 3Racing but have heard great reviews about the Ballistic. My question is this, how is the extension handled? The 3Racing has a center drive that...
02-06-2006, 11:36 AM
Replies: 30
Views: 1,539
Posted By psrumors

RE: RC recomendation for my boy's 9th birthday

We had the ESC Xl-1 and it was crap
02-06-2006, 07:32 AM
Replies: 30
Views: 1,539
Posted By psrumors

RE: RC recomendation for my boy's 9th birthday

If you buy the Stampede be prepared for a new motor and speed controller. We bought one for Christmas for our 7 year old and after 2 motors and ESCs from Traxxas we bought aftermarkets. The truck is...
02-04-2006, 11:02 PM
Replies: 2
Views: 475
Posted By psrumors

RE: Nitro Stampede Fuel Hose Configuration

Thanks, that's what I needed to know.
02-04-2006, 09:53 PM
Replies: 21
Views: 1,400
Posted By psrumors

RE: I have read till I am blue in the face!! OS .18TM or RB TM323

Well, I am 2 tanks into the break-in and can already tell this should be fun. I hope the rain holds out tomorrow and can finish the break-in.
02-04-2006, 08:45 PM
Replies: 2
Views: 475
Posted By psrumors

Nitro Stampede Fuel Hose Configuration

I am in the process of putting together a used Nitro Stampede I bought. None of the exploded view show this so I need your help.

The fuel lines, I am assuming the bottom outlet on the fuel tank...
02-04-2006, 09:42 AM
Replies: 21
Views: 1,400
Posted By psrumors

RE: I have read till I am blue in the face!! OS .18TM or RB TM323

What do you "watch for"? Is the back plate coming loose or what?
02-02-2006, 07:14 PM
Replies: 21
Views: 1,400
Posted By psrumors

RE: I have read till I am blue in the face!! OS .18TM or RB TM323

Thanx for all the info guys. I ended up buying the RB this evening. It will be here tomorrow. I ended up with the RB for one reason, it's weight. We went out bashing today and since I had removed the...
02-02-2006, 12:25 PM
Replies: 21
Views: 1,400
Posted By psrumors

RE: I have read till I am blue in the face!! OS .18TM or RB TM323

I don't, but I think the OS will wind up faster due to it's smaller displacement. Am I wrong, usually smaller motors will wind out faster. Does not mean the truck will be going faster.

Make...
02-02-2006, 09:17 AM
Replies: 21
Views: 1,400
Posted By psrumors

I have read till I am blue in the face!! OS .18TM or RB TM323

I know this has been asked, compared, sliced, diced and trampled on but I am having a hard time deciding. My 2.5r out of my Revo is going into my son's Stampede, it's the cheapest quickest way to get...
01-26-2006, 09:45 PM
Replies: 6
Views: 346
Posted By psrumors

RE: new revo, front wheels have a slight toe out, is that normal....?

A little bit of toe out in the front (.5-1.5 degrees) and a little toe in in the rear (.5-1.0 degrees) will help the truck tract straight also.
01-24-2006, 07:06 AM
Replies: 8
Views: 333
Posted By psrumors

RE: Hitec servo sugestions?

I doubt anyone would notice the differnce of .04, I know I wouldn't. For the same price and at that speed I would go with the torque.
01-23-2006, 10:46 PM
Replies: 8
Views: 333
Posted By psrumors

RE: Hitec servo sugestions?

What are you planning on doing with the truck? If bashing either is fine, I personally would go with the most torque for bashing. If racing I would go with the fastest.
01-23-2006, 08:07 PM
Replies: 2
Views: 356
Posted By psrumors

RE: steering ????s

Take a look at this, it is excellent

Revo Steering Setup
01-23-2006, 05:43 PM
Replies: 17
Views: 2,040
Posted By psrumors

RE: No Aluminum Bulkheads for the Revo?

Well, the crack didn't come from a tight screw rather a bad landing. I was hoping to use aluminum inner parts (bulkheads, shock braces, etc) with plastic outer parts to absorbed and break from major...
01-23-2006, 05:38 PM
Replies: 8
Views: 333
Posted By psrumors

RE: Hitec servo sugestions?

As for the volts, you will be using 6 at the finish of a charge.

Which servos are you looking at? I just installed a 5945 in my Revo and am very happy with it's performance.

Yes, metal...
01-23-2006, 07:33 AM
Replies: 17
Views: 2,040
Posted By psrumors

No Aluminum Bulkheads for the Revo?

Why not? I have to replace the front bulkhead and would really like to go with aluminum. Does no one make aluminum bulkheads for the Revo? I have a stress crack where the skid plate screw goes into...
01-22-2006, 10:59 AM
Replies: 22
Views: 1,141
Posted By psrumors

RE: My finished winter project!(pics!)

Looks nice. What did you use for the battery tray?
01-21-2006, 10:27 AM
Replies: 1
Views: 286
Posted By psrumors

RE: Factory setings

High Speed Needle is 4 turns out from closed
Low Speed Needle is srew head is flush with the surrounding metal
01-21-2006, 10:22 AM
Replies: 0
Views: 198
Posted By psrumors

Servo Connectors and Torque

What are the torque ratings of the stock Revo Servos? Also, what type connectors do they use, J,Z?
Showing results 1 to 25 of 45
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.