RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: villalbi2003
Showing results 1 to 10 of 10
Search took 0.63 seconds.
05-19-2015, 12:16 PM
Replies: 2,031
Views: 676,579
Posted By villalbi2003

HI Brenner what do you think about the new...

HI Brenner
what do you think about the new hacker motor in develop specially for contradrive, C54L 4 pole more couple less consuption and low heat and 70 gram less as weight!
link:...
02-23-2015, 12:43 PM
Replies: 2,031
Views: 676,579
Posted By villalbi2003

Hy brenner very good solution for bearing and...

Hy brenner
very good solution for bearing and for weigh reduction,
i worry about the the link system to motor, with this new system you have all gearbox propeller and spinner without any
support,...
04-26-2013, 12:12 PM
Replies: 325
Views: 107,428
Posted By villalbi2003

RE: ARIXTRA Build Thread by ISAAC NAJARY

hi Isaac
what kind of clear coat do you use?
i use acrilic color for paint but i have some problem with clear coat,
normally the type used for cars are very heavy and diffucolt to apply.
...
12-31-2012, 04:22 AM
Replies: 115
Views: 57,436
Posted By villalbi2003

RE: New OXAI CITRIN by Wolfgang and Roland Matt

hello
about the nose damage of Citrin with Hacker Q80, i see another same case exactly,so i think must to take in consideration the action by a big
ring rotate of motor, i think it work like a...
11-07-2012, 12:18 PM
Replies: 199
Views: 63,003
Posted By villalbi2003

RE: CAELESTIA NEW F3A 2011

Hi at all
Continue the fly of Our Caelestia,(my and my son pilot)and after every fly i am very full satisfied as the airplane flies....
very very well: we can test some monouvre very critical...
09-21-2012, 12:37 AM
Replies: 199
Views: 63,003
Posted By villalbi2003

RE: CAELESTIA NEW F3A 2011

Hello to all
I attach some pictures of my Caelestia, tested a few weeks ago.
From the photos you can see the new position of landing gear (lower than the original), the addition of an inside...
10-01-2007, 04:12 PM
Replies: 9
Views: 1,810
Posted By villalbi2003

RE: YS160DZ Fuel Draw Problem

also i have a problem with my YS160DZ,the same problem to not be drawing fuel,and many my friends too.Are you sure this is a little problem or is a wrong project,for fuel pump?
I have notice that...
07-18-2007, 04:00 PM
Replies: 2
Views: 603
Posted By villalbi2003

pressure pump fuel

Hi guys
have someone notice about the standard pressure there is betweene the outlet of fuel pump and inlet of carburetor in the YS160DZ.
How many psi about.
This information help me to start...
06-03-2007, 04:01 PM
Replies: 3
Views: 640
Posted By villalbi2003

valve ys160DZ

HI
I have an YS160DZ with more than 100 fly on,i have disassembly the head and i want to change
the valve(the exaust valve is in bad condition and the compression is not better)
It is...
05-28-2007, 08:59 AM
Replies: 1
Views: 417
Posted By villalbi2003

spare parts

Hi Guys!
I am an italian modeller and i have three YS160DZ ,two are new and begin to run now, one is with 100 fly old,now i want to substitute some parts ,like piston segment,bearing, gasket and so...
Showing results 1 to 10 of 10


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.