RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: arobatto
Showing results 1 to 13 of 13
Search took 0.61 seconds.
Forum: O.S. Engines Support
08-23-2011, 04:00 PM
Replies: 2
Views: 644
Posted By arobatto

RE: FS-200S-P Leaking Pressure Regulator

Bax,

I should have done my homework. I read similar posts and it looks as if the diaphragm is shot. Would it be better if I sent it in for repair, or just buy the carburetor body?
Forum: O.S. Engines Support
08-23-2011, 01:08 PM
Replies: 2
Views: 644
Posted By arobatto

FS-200S-P Leaking Pressure Regulator

Greetings Mr. Bax,

I have an FS-200S-P that is running great at all rpm ranges, yet it is weeping/dripping fuel from the slot at the pressure regulator. The engine has about three gallons of...
Forum: Kit Building
02-24-2011, 02:15 PM
Replies: 6
Views: 2,004
Posted By arobatto

RE: Precision cut kits

Yes, they are. I was just there having coffee and melt-aways while they were on a short break. They are extremely busy and Judy should contact you soon.

Regards,

Alex Robatto
Hopewell...
Forum: Giant Scale Aircraft - General
02-20-2011, 07:51 AM
Replies: 16
Views: 2,565
Posted By arobatto

RE: Scale Pilot

The cigarette too? Nice detail. I like the watch! He has the likeness of Howard Hughes ...

Alex Robatto
Hopewell Valley Modelers
Forum: Giant Scale Aircraft - General
02-17-2011, 09:00 AM
Replies: 16
Views: 2,565
Posted By arobatto

RE: Scale Pilot

I used the Great Planes; GPMQ9061 Pilot Figure 1/4 Civilian Unpainted

Great Planes Pilot Figures

I like to paint figures (from my scale plastic building days - soon to be again, I hope)
...
Forum: Kit Building
02-12-2011, 10:21 PM
Replies: 11
Views: 1,307
Posted By arobatto

RE: Venting my rage about parchment paper

That had to suck! I hate it when sh_t like that happens! The person recommending parchment paper probably had it confused for wax paper as they are both are used in baking. However, wax paper is...
Forum: Kit Building
02-11-2011, 09:25 PM
Replies: 23
Views: 2,050
Posted By arobatto

RE: T/F wood pecker???

In the 30+ years I've been building and covering models, I have yet to try this contraption - or anything like it. My good friend and experienced builder swears by it so I convinced myself to buy one...
Forum: Kit Building
02-11-2011, 09:00 PM
Replies: 1,251
Views: 274,076
Posted By arobatto

RE: Where Have All The Kits Gone ?

Greetings kit builders,

I would like to put in a plug for my good friends Larry and Judy Katona, owners of Precision Cut Kits

PCK

I am currently finishing their Pro-Line Aerobatic...
Forum: O.S. Engines Support
09-07-2010, 09:25 AM
Replies: 5
Views: 1,056
Posted By arobatto

RE: FS-91S No Pump, Needle Valve Setting

Thanks for your quick reply sir. Since I don't have the original manual, may I ask if if the following are the correct catalog numbers?

Needle: OSMG7062
Carb. Body: OSMG3578



Thanks...
Forum: O.S. Engines Support
09-06-2010, 07:08 PM
Replies: 5
Views: 1,056
Posted By arobatto

FS-91S No Pump, Needle Valve Setting

Greetings Mr. Baxter,

I have a 2000 FS-91S without a pump that needs to have the needle valve fully closed to run lean enough. In searching this forum I learned that it may be a worn needle...
Forum: "1/2 A" & "1/8 A" airplanes
04-25-2006, 04:53 PM
Replies: 14
Views: 1,264
Posted By arobatto

RE: Shrike

Tashley,

May I ask were you purchased your spinner for your 1/2A Shrike? I'm having some difficulty obtaining a 1-1/4" spinner.

Regards,

Alex Robatto
Forum: "1/2 A" & "1/8 A" airplanes
04-23-2006, 02:08 PM
Replies: 4
Views: 1,324
Posted By arobatto

Voltage For Norvel Glow Plug

Hello all!

About two years ago, I have purchased a NIB 1998 vintage Norvel AME 061. Now that I have the 1/2A bug, I decided to test run this Russian powerhouse. I tested the glow plug for...
Forum: "1/2 A" & "1/8 A" airplanes
04-20-2006, 04:03 PM
Replies: 6
Views: 876
Posted By arobatto

Looking for 1-1/4" Spinner for 1/2A Shrike

Howdy yall,

As some of you may know, Lanier's plans calls for a 1-1/4" spinner for their 1/2A Shrike. I have already purchased the Dubro Norvel spinner. However, I really like the clean lines...
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.