RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: CPT Moonlight
Showing results 1 to 15 of 15
Search took 0.60 seconds.
Forum: Electric Pattern Aircraft
02-21-2010, 09:02 AM
Replies: 1,858
Views: 306,165
Posted By CPT Moonlight

RE: Sebart Wind 110

Work is no excuse for not flying, if you went flying you would do twice as much work, and your boss would give you a pay rise???

Happy flying
CM
Forum: Glow Engines
03-28-2009, 09:33 AM
Replies: 14
Views: 8,997
Posted By CPT Moonlight

RE: ASP 1.20 4 Stroke Valve Settings

Your RPM is the same as my ASP 120 4s with a 16x6 APC ,I have a 65" Extra with a 15x7 fare better performance with this engine

Regards Ivan
Forum: Classic RC Pattern Flying
08-13-2008, 12:26 PM
Replies: 303
Views: 21,967
Posted By CPT Moonlight

RE: if you want a curare plan

I would love to receive the Plan, [email protected]

All the best Ivan
Forum: E-Flight Power Sources
04-29-2004, 01:56 PM
Replies: 7
Views: 1,511
Posted By CPT Moonlight

RE: Charging LiPo with a L-ion Charger

Hi Sprarry, I set 3 cell (3.7 X3=11.1 V) and 3 amp. My setup is 3s 3p all 1500 KoK = 4500 Ah, If the charger was able to go to 4.5 amps that would be less time to charge, but the Prodigy only goes...
Forum: E-Flight Power Sources
04-11-2004, 10:03 AM
Replies: 6
Views: 713
Posted By CPT Moonlight

RE: Motor is Cutting Out

I had this problem with a AXI 2820/10 It turned out that the dean module was to near the receiver.
(just) a thought

IVAN
Forum: Brushed/Brushless motors, speed controls, gear drives
04-11-2004, 09:18 AM
Replies: 2
Views: 467
Posted By CPT Moonlight

RE: Phonenix 45 Settings

Ok Phil will S Palmer a call, Many Thanks.

Ivan
Forum: Brushed/Brushless motors, speed controls, gear drives
04-10-2004, 09:52 AM
Replies: 2
Views: 467
Posted By CPT Moonlight

Phonenix 45 Settings

I have a CC Phoneix 45 Kok 1500 3s-3p MM AXI 2820/10
What are the best settings for this Motor ( I have changed the cut off to 9V) but would like soom advice on the other settings.
Forum: Brushed/Brushless motors, speed controls, gear drives
04-05-2004, 12:32 PM
Replies: 5
Views: 841
Posted By CPT Moonlight

RE: CC Phoenix 45 stops after Full Throttle

Many thanks to all, Ive found the tab on one of the one pack has torn off,Ill go back to soldering to PCB and not soldering the tabs together, you learn by your mistakes and I will go to a 10x7 prop ...
Forum: Brushed/Brushless motors, speed controls, gear drives
04-04-2004, 11:02 AM
Replies: 5
Views: 841
Posted By CPT Moonlight

CC Phoenix 45 stops after Full Throttle

My CC P45 speed controller shuts down when I come down from (full throttle 30 sec)and then keeps on cutting out when I restart.
My setup AXI2820/10 Lipo 3s-3p 1500 -11x7 prop I have only reset...
Forum: Electric General Discussion
03-14-2004, 12:54 PM
Replies: 4
Views: 479
Posted By CPT Moonlight

Secure that Battery

Have you got a good way of securing battery's ??????
Forum: E-Flight Power Sources
03-14-2004, 12:30 PM
Replies: 7
Views: 1,511
Posted By CPT Moonlight

RE: Charging LiPo with a L-ion Charger

DW I monitored the complete charge and every thing went good. Ivan
Forum: E-Flight Power Sources
03-14-2004, 11:16 AM
Replies: 7
Views: 1,511
Posted By CPT Moonlight

RE: Charging LiPo with a L-ion Charger

Hi D W The cells are Kokam 1500, I set the charger to 1.5 & 11.1V and it did the rest , It was a 3 series pack. The charger also charges NiCd-NiMh- PB- Li-ion, Charge rate 0.1A~3A 100mA steps...
Forum: E-Flight Power Sources
03-14-2004, 09:51 AM
Replies: 7
Views: 1,511
Posted By CPT Moonlight

Charging LiPo with a L-ion Charger

Hi, I have a Pro Peak Prodigy Charger It charges L-ion 1-3 cells,I have charged 3 Cell Li-Po with it and the finished charge goes to 12.6V settle down to 12.48V. It doesn't state it charges Li-Po...
Forum: E-Flight Power Sources
02-13-2004, 01:54 PM
Replies: 5
Views: 719
Posted By CPT Moonlight

RE: Wiring Li polys

Thanks Lad's for the tables thats all I need

Ivan
Forum: E-Flight Power Sources
02-11-2004, 01:52 PM
Replies: 5
Views: 719
Posted By CPT Moonlight

Wiring Li polys

Could someone tell me if 1.5m 12 Amp silicone is OK for wiring K 1500 3S-3P.
The pack will be driving AXI 2820/10. ???[8D]
New to E Flight
Showing results 1 to 15 of 15


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.