RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Mark Dennis
Showing results 1 to 8 of 8
Search took 0.11 seconds.
Forum: 3D Flying!
06-05-2006, 11:56 PM
Replies: 1,869
Views: 234,152
Posted By Mark Dennis

RE: AeroWorks Edge 540T 46-60?

A simple search on google can provide you with the info in about a minute.
30*c= 86*f we fly at 6000' and the satio has tons of power on a 90* day so you will be fine. The ones I flew up here had...
Forum: 3D Flying!
11-30-2005, 11:03 PM
Replies: 1,869
Views: 234,152
Posted By Mark Dennis

RE: AeroWorks Edge 540T 46-60?

The prop will most definatly clear with room to spair. The pull-pull it comes with works great.
Forum: 3D Flying!
11-30-2005, 05:20 PM
Replies: 1,869
Views: 234,152
Posted By Mark Dennis

RE: AeroWorks Edge 540T 46-60?

The .91 works great in the edge we tested it a .61 and a .46 on the edge and the .91 one was the best overall choice for 3D. You are right about the weight also it relly wouldnt make since to put the...
Forum: 3D Flying!
11-19-2005, 08:54 PM
Replies: 1,869
Views: 234,152
Posted By Mark Dennis

RE: AeroWorks Edge 540T 46-60?

Are you sure you are checking the cg in correct place? I have seen and flown 3 of these with the 100 and all balanced dead on or just a little nose heavy. I have finally gotten a good vid and we hope...
Forum: 3D Flying!
11-15-2005, 06:50 PM
Replies: 1,869
Views: 234,152
Posted By Mark Dennis

RE: AeroWorks Edge 540T 46-60?

Ok guys we finally got this one figured out. All you have to do is flip the mount over so that the webing is opposite the motor and everything will clear. If you have any questions on this please...
Forum: 3D Flying!
11-13-2005, 07:43 PM
Replies: 1,869
Views: 234,152
Posted By Mark Dennis

RE: AeroWorks Edge 540T 46-60?

Can you measure the length of the mount. that definatly looks like the problem if thats the case we can send you a new one. call the shop tomorrow tell them that you talked to mark and give them the...
Forum: 3D Flying!
11-03-2005, 09:59 PM
Replies: 1,869
Views: 234,152
Posted By Mark Dennis

RE: AeroWorks Edge 540T 46-60?

Both are vary stable and as far as coupiling goes there isnt even enough to trim out. I can do knifeedge circles all day long in any deirection and the plane is rock solid no matter what I do. It is...
Forum: 3D Flying!
11-03-2005, 08:58 PM
Replies: 1,869
Views: 234,152
Posted By Mark Dennis

RE: AeroWorks Edge 540T 46-60?

Twister I have been flying our prototype for about 2 mounths know and all I have to say is wow. The plane flys very light wich makes since being that its only 6#'s with a .91. This weight is not at...
Showing results 1 to 8 of 8


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.