RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: TStick
Showing results 1 to 11 of 11
Search took 0.05 seconds.
Forum: Twin & Multi Engine RC Aircraft
03-02-2008, 09:55 AM
Replies: 1,138
Views: 357,903
Posted By TStick

RE: OV-10 Bronco 81"

rrudytoo,
I built a horiz stab with ribs and spars and have the elevator servo IN the stab. With stab at o degrees, the engines are at 2 degrees negative, the wing at 1 degree positive. The port...
Forum: Twin & Multi Engine RC Aircraft
02-04-2008, 07:56 PM
Replies: 1,138
Views: 357,903
Posted By TStick

RE: OV-10 Bronco 81"

Ken,
Nice pics. I'll attach some pics as soon as I learn the process.
Ted
Forum: Twin & Multi Engine RC Aircraft
02-03-2008, 05:58 PM
Replies: 1,138
Views: 357,903
Posted By TStick

RE: OV-10 Bronco 81"

Telemaster 56,
1. Spektrum receivers are mounted just inside the tailcone. I made an extra former from liteply for the tail cone. It's hinged on the port side. Rare earth magnets and a small...
Forum: Twin & Multi Engine RC Aircraft
02-01-2008, 08:18 PM
Replies: 1,138
Views: 357,903
Posted By TStick

RE: OV-10 Bronco 81"

Telemaster 56,
Radical R/C markets a switch that can plug into any channel of the Rx and controls any electrical function. I used Radio Shack micro switches placed next to a servo that controls...
Forum: Twin & Multi Engine RC Aircraft
02-01-2008, 08:08 PM
Replies: 1,138
Views: 357,903
Posted By TStick

RE: OV-10 Bronco 81"

Duflid,
I used Precision Cut Kits for my parts. Their cut parts look and fit great. Each piece is labled. The sheet stock is very good quality also. I build a 3-piece wing anad the holes in the...
Forum: Twin & Multi Engine RC Aircraft
01-03-2008, 09:59 AM
Replies: 1,138
Views: 357,903
Posted By TStick

RE: OV-10 Bronco 81"

Cando & Fancman,
Thanks for the info on flap/elev combo for take off. I'll use that setup for the next flight attempt.
TStick
Forum: Twin & Multi Engine RC Aircraft
12-31-2007, 03:51 PM
Replies: 1,138
Views: 357,903
Posted By TStick

RE: OV-10 Bronco 81"

CanCo,
My high speed taxi was an attempt to get enough ground speed to lift off and fly. It was not a TEST. Since the nose gear compressed, the wing developed a neg. angle and the plane wouldn't...
Forum: Twin & Multi Engine RC Aircraft
12-30-2007, 11:57 AM
Replies: 1,138
Views: 357,903
Posted By TStick

RE: OV-10 Bronco 81"

CanDo,
I hadn't realized the Uravitch site was down. I bought plans, cowls, etc from Rich. But Precision Cut Kits provided the kit, which was excellent. Perhaps they will buy the rights to the...
Forum: Twin & Multi Engine RC Aircraft
12-29-2007, 02:39 PM
Replies: 1,138
Views: 357,903
Posted By TStick

RE: OV-10 Bronco 81"

CanDo,
I'd love to share pics of my project as soon as I learn the proceedure. I built the Bronco from Uravitch plans. I modified them a little. I stretched the wing by a rib bay, bringing it to...
Forum: Twin & Multi Engine RC Aircraft
12-27-2007, 10:28 PM
Replies: 1,138
Views: 357,903
Posted By TStick

RE: OV-10 Bronco 81"

Telemaster56,
I painted my canopy frames on the outside. It was fastened with goop and screws. I painted a coat of gray primer first, to match the interior of the cockpit. The finish coat of the...
Forum: Twin & Multi Engine RC Aircraft
03-08-2005, 03:39 PM
Replies: 1,138
Views: 357,903
Posted By TStick

RE: OV-10 Bronco 81"

FLYALAN,

Just read your comments about operating gear doors on your Bronco. I have a Bronco in the planning stage. I build a P-61 Black Widow from Don Smith plans with functional gear doors. ...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.