Notices
Search: Posts Made By: LOCKTUMBLER
Showing results 1 to 14 of 14
Search took 0.32 seconds.
Forum: Glow Engines
12-16-2016, 01:47 PM
Replies: 2,218
Views: 187,928
Posted By LOCKTUMBLER

I'll try it on my standard fuel, 'Southern model...

I'll try it on my standard fuel, 'Southern model craft synthetic' - 15%synth oil/2%castor/10%nitro/73%methanol. But, 10% nitro may be too much, if so I'll use the same fuel but with only 5% nitro.
Forum: Glow Engines
12-16-2016, 01:20 PM
Replies: 2,218
Views: 187,928
Posted By LOCKTUMBLER

Got one I've rebuilt; new ring, lapped bore, new...

Got one I've rebuilt; new ring, lapped bore, new con-rod, new bearings and an ASP91 carb(smaller choke) with spigot sleeve to fit. Standard silencer. 5%nitro/20%castor/75%methanol; 16 X 8 wood prop @...
07-09-2015, 12:43 PM
Replies: 398
Views: 47,985
Posted By LOCKTUMBLER

earl, all my Indian Mills(3) have intake slots in...

earl, all my Indian Mills(3) have intake slots in the liner and all my Irvine Mills(3) have two holes that are in line.
HTH
07-09-2015, 12:40 PM
Replies: 398
Views: 47,985
Posted By LOCKTUMBLER

KE51, I get 7,900rpm using a Topflight 9 x 4 and...

KE51, I get 7,900rpm using a Topflight 9 x 4 and 6,500rpm using a Topflight 10 x 4, fuel is Modeltechnics D1000 http://www.modeltechnics.com/diesel.htm Didn't notice excessive vibs on my 'curry'...
06-08-2015, 03:57 AM
Replies: 398
Views: 47,985
Posted By LOCKTUMBLER

Well I've done some dismantling and...

Well I've done some dismantling and investigation. I took the opportunity to take apart one of my other Irvine Mills 1.3 Ser.No. 01622, its developed a rough ball race, and use it as comparison. This...
06-07-2015, 11:13 AM
Replies: 398
Views: 47,985
Posted By LOCKTUMBLER

Hi, hope you can help me put my mind at rest or...

Hi, hope you can help me put my mind at rest or possibly otherwise. Recently obtained an Irvine Mills 1.3 described as BNIB with box, all documents and other bits. After I recieved it I gave it a...
Forum: Glow Engines
09-20-2014, 11:01 AM
Replies: 1,776
Views: 166,559
Posted By LOCKTUMBLER

If its the latter type with the crankcase...

If its the latter type with the crankcase breather from the cam box to the inlet manifold I'd give that a good check out, externally and internally, for damaged pipe/loose nipples/leaks/blockages....
Forum: ARF or RTF
03-26-2014, 02:49 AM
Replies: 1,289
Views: 136,607
Posted By LOCKTUMBLER

Just got myself one of these, about to go through...

Just got myself one of these, about to go through the kit contents and check its all there and if I've got the short UC to fusalage fairings (hope not). I've got a selection of engines on the bench;...
09-25-2013, 01:10 AM
Replies: 1,820
Views: 259,963
Posted By LOCKTUMBLER

How I wish I got one of these when they were...

How I wish I got one of these when they were available! Oh well, another one to add to my ever growing list of lifes regrets.
Forum: Gas Engines
07-13-2010, 10:16 AM
Replies: 893
Views: 105,569
Posted By LOCKTUMBLER

RE: CRRC 40cc kit

You will probably have to make a new sensor holder similar to the one marketed by Agape Racing and Hobby for their RcExel CDI conversion [:o]. ...
Forum: Gas Engines
03-09-2010, 06:09 AM
Replies: 662
Views: 76,103
Posted By LOCKTUMBLER

RE: DLE30 rear induction conversion!

Cyberwolf,
email and deposit sent.
Forum: Gas Engines
02-11-2010, 03:12 AM
Replies: 20
Views: 3,225
Posted By LOCKTUMBLER

RE: New small gasser

aussiesteve,
Many thanks for the prompt reply.
Didn't want to end up buying a V1 when I knew there was a V2 available.
Looks like I will be buying yet another engine to add to my three figure...
Forum: Gas Engines
02-10-2010, 10:28 AM
Replies: 20
Views: 3,225
Posted By LOCKTUMBLER

RE: New small gasser

Been following the RCGF and the Aerovate threads with interest and now this one. Can some one tell me the difference between the V1 and V2 of the JC 28? Also, is this offering in the UK a V1 or V2...
Forum: Gas Engines
04-24-2009, 10:31 AM
Replies: 893
Views: 105,569
Posted By LOCKTUMBLER

RE: CRRC 40cc kit

Hi to everyone from a depressed UK.
I've built one of these engines to go in my 'Pacific Models Gee Bee Y 120' but I could use an inverted wraparound pitts silencer.
Jedijody, you made mention of...
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.