Search: Posts Made By: bunsen
Showing results 1 to 25 of 129
Search took 0.16 seconds.
Forum: Futaba Radios Direct support forum 10-09-2017, 04:29 AM
Replies: 3
Views: 140
Posted By bunsen
Thanks i will give it a try. ray

Thanks

i will give it a try.

ray
Forum: Futaba Radios Direct support forum 10-08-2017, 06:00 PM
Replies: 3
Views: 140
Posted By bunsen
Bax From looking around it seems that the...

Bax

From looking around it seems that the only way to access DG1 and DG2 from a 14SG using dual R7008SB receivers to is connect a Futaba SBD-1 SBUS decoder to the second "mode D" receiver SBUS...
Forum: Futaba Radios Direct support forum 10-02-2017, 05:48 PM
Replies: 3
Views: 140
Posted By bunsen
14sg access to DG1 and DG2 with dual 7008SB

I have a 14sg transmitter and have used the 6014FS receiver with access to 12 proportional channels and the DG1/DG2 on/off channels with no issues.

Going forward would like to be able to utilize...
Forum: Futaba Radios Direct support forum 09-17-2017, 05:55 AM
Replies: 3
Views: 222
Posted By bunsen
Thanks I missed that. ray

Thanks I missed that.

ray
Forum: Futaba Radios Direct support forum 09-16-2017, 04:36 PM
Replies: 3
Views: 222
Posted By bunsen
R6014HS Replacement ?

Given that the 14 Channel R6014HS is listed as "unavailable" on the Futaba RCV Web Site is there a suggested alternative or an updated version coming along in the near term?

Perhaps it is just a...
Forum: Classic RC Pattern Flying 09-15-2017, 06:44 AM
Replies: 12
Views: 561
Posted By bunsen
Skyhawk940 Looks great. :) Like the...

Skyhawk940

Looks great. :)

Like the color scheme.

Thanks for posting.

Ray
Forum: Classic RC Pattern Flying 09-11-2017, 12:56 PM
Replies: 12
Views: 561
Posted By bunsen
Thanks That may be the best thing to do. ...

Thanks

That may be the best thing to do.

Ray
Forum: Classic RC Pattern Flying 08-13-2017, 07:56 AM
Replies: 12
Views: 561
Posted By bunsen
No i am hopeful that they will respond. ...

No

i am hopeful that they will respond.

if I hear back will post info.

ray
Forum: Classic RC Pattern Flying 08-10-2017, 01:44 PM
Replies: 12
Views: 561
Posted By bunsen
Thanks Skyhawk Checked the site and kits are...

Thanks Skyhawk

Checked the site and kits are out of stock.

Left a message using their web site contact info asking if they will have kits in the near term.

Also left a phone message asking...
Forum: Classic RC Pattern Flying 08-03-2017, 07:09 AM
Replies: 12
Views: 561
Posted By bunsen
Kaos 120 ??

Hi

I see where Eureka sells short kits for a a Kaos 60, Super Kaos 60 and a Kaos 90.

They also sell a foam wing kit for a Kaos 120 but don't see a set of plans anywhere.

Was set of plans...
Forum: Futaba Radios Direct support forum 06-09-2017, 08:15 AM
Replies: 3
Views: 204
Posted By bunsen
Thanks BAX I have not used the default rate....

Thanks BAX

I have not used the default rate. I suppose because I like to have a DR Rate correspond to a switch setting but no reason not to use the default and just set the switch position that I...
Forum: Futaba Radios Direct support forum 06-08-2017, 07:03 PM
Replies: 3
Views: 204
Posted By bunsen
BAX Reading thru the Futaba manual again it...

BAX

Reading thru the Futaba manual again it seems that I could use the Priority function built into the 1 > 5 Dual Rate Options.

As I understand if more than one "rate" switch is "ON" that the...
Forum: Futaba Radios Direct support forum 06-08-2017, 12:09 PM
Replies: 3
Views: 204
Posted By bunsen
Four indépendant Dual Rates on 14SG

I have a 14SG with three DR (Dual Rate) settings for elevator, rudder and Aileron settings on SG (Low, Medium, and High) and three flap settings through a PIMIX (none, half and full ) on SB.

I...
Forum: Aerodynamics 05-19-2017, 01:43 AM
Replies: 29
Views: 1,863
Posted By bunsen
I had not considered that a forward CG would...

I had not considered that a forward CG would cause an airplane to land faster. Is it assuming that the elevator travel is not adequate to increase the AOA to get a slower speed or something else?...
Forum: RC Pattern Flying 05-01-2017, 02:43 PM
Replies: 1
Views: 523
Posted By bunsen
VENUS II Replacement

Have been flying a GP VENUS II airplane that I really enjoyed but lost it last week. :(

Have been looking around for a replacement ARF that would take a DLE 20cc engine that would be appropriate...
Forum: AMA Discussions 03-10-2017, 08:50 PM
Replies: 4
Views: 393
Posted By bunsen
Yes you can do that electronically. When you...

Yes you can do that electronically.

When you submit the sanction on-line it will ask you if you want to order additional advertising. There are two sizes to choose from. You pick the number of...
Forum: AMA Discussions 03-10-2017, 06:15 PM
Replies: 4
Views: 393
Posted By bunsen
Hi As a CD you can submit a sanction for an...

Hi

As a CD you can submit a sanction for an AMA event totally on-line and receive the sanction approval via E-Mail.

I just did this for a 2017 club event.

At the AMA Web site:

1. Go to...
Forum: Kit Building 01-26-2017, 11:11 AM
Replies: 60
Views: 2,844
Posted By bunsen
Hi Bob One suggestion for filling small gaps...

Hi Bob

One suggestion for filling small gaps like that is to make some strips from 1/32 " and/or 1/16" balsa sheet to the width of the rib, say 1/8 ", by about an inch long. Than place the end...
Forum: Kit Building 01-11-2017, 10:21 AM
Replies: 60
Views: 2,844
Posted By bunsen
Hi Bob I am in. Ray

Hi Bob

I am in.

Ray
Forum: Futaba Radios Direct support forum 08-11-2016, 04:41 PM
Replies: 1
Views: 301
Posted By bunsen
14sg CMBFLP to ELE motion with "slow" flaps

Have set up my 14SG with a PMIX to provide Flap to Elevator compensation without using the MOTOR function to slow Flap deployment.

Have used the "Servo Speed" function to slow "FLP" and "FLP2"...
Forum: Batteries & Chargers 07-19-2016, 04:19 AM
Replies: 51
Views: 3,850
Posted By bunsen
Dan I have the X4 Charger and to...

Dan

I have the X4 Charger and to discharge/load test my A123 LIFE batteries use the NIMH program and set the end point voltage to +5 or +5.5 volts.

Cheers

Ray
Forum: Questions and Answers 07-17-2016, 04:22 PM
Replies: 7
Views: 380
Posted By bunsen
If you are looking for a RCV controlled relay I...

If you are looking for a RCV controlled relay I have used:

Dimension Engineering

Pico Switch and Battle Switch that work off nominal +5V RCV SERVO output.

Ray
Forum: RC Warbirds and Warplanes 04-16-2016, 05:38 PM
Replies: 10
Views: 1,416
Posted By bunsen
You may find this website useful . P-47...

You may find this website useful .

P-47 Cockpit Cockpit 360 visual tour from the Airforce Museum.

http://www.nmusafvirtualtour.com/media/028/P-47D%20Cockpit.html
...
Forum: Futaba Radios Direct support forum 03-18-2016, 05:28 AM
Replies: 3
Views: 493
Posted By bunsen
CK1 Note that works as shown below but...

CK1

Note that works as shown below but trying to figure out how to do this without having to use the MOTOR function.
Looked at the TX and Model type is:

Type: Airplane
Wing: ...
Forum: Futaba Radios Direct support forum 03-17-2016, 10:38 AM
Replies: 3
Views: 493
Posted By bunsen
14SG slow flap deployment with MOTOR function to get proper Flap to Elev mix

Bax

I have a 14SG in Airplane mode, 2 flap servos, 2 aileron servos, 2 elevator servos

Chan # Function

1 Left Aileron
2 Left Elevator
3 Throttle
4. ...
Showing results 1 to 25 of 129



Forum Jump


All times are GMT -8. The time now is 12:13 PM.