Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: pe reivers

Page 1 of 40 1 2 3 4

Search: Search took 1.29 seconds.

  1. Replies
    12
    Views
    1,298

    RE: Evolution 58GX2 prop question

    MVVS makes a prop drill jig, item # 3380
  2. Replies
    1
    Views
    576

    RE: where must the B on the piston face

    I am not sure about the 116, since I never took one apart.
    To be sure, contact mvvs@mvvs.cz , provide them with the engine serial number.
  3. Replies
    4
    Views
    514

    RE: High speed needle issue

    The idle needle provides fuel for both idling and high speed running. The high speed needle becomes active at about half throttle (more or less)
    So if you open the high needle, you need less idle...
  4. RE: What's The Inside of a Canister Muffler Look Like

    Do a patent search on Weyershauser. In patents, you get drawings and full explanations of the contraptions,
    Like 3W: ...
  5. Replies
    111
    Views
    10,343

    RE: Fuchs Aerosave

    So which one of the two was run on aerosave?

    Four strokes have a lot of gas blow-by, and the crankcase, which is not ventilated like a two stroke, thus fills with sludge consisting of moisture,...
  6. Replies
    9
    Views
    2,322

    RE: 3W-110 vs MVVS/Evolution 116

    who actually flew the evolution engine?
  7. Replies
    2
    Views
    802

    RE: MVVS Carburetor

    If I had to do it, I would saw off the plastic part, and press in a brass tube.
    The plastic part will probably break if you try to twist it out
  8. Replies
    8
    Views
    1,580

    RE: MVVS tuned pipe 3268

    Just add some extra length, and then shorten one inch at a time until you are satisfied. No one can predict exactly what happens when you try out a new pipe/engine combination.
  9. Replies
    3
    Views
    725

    RE: mvvs help 26 redhead

    check out my web page.
    look under accessories.
  10. Replies
    29
    Views
    1,795

    RE: after run?

    I use wd40 to keep my donkey's feet and face free of flies and mosquitos.These critters don't like the stuff[8D]
    In addition, I use it liberally to clean engines and to get rid of moisture where I...
  11. Replies
    3
    Views
    725

    RE: mvvs help 26 redhead

    Vlach ignitions are a thing of the past.MVVS now produces ICU conversion sets, so the vlach equipped engines can be serviced.
  12. Replies
    4
    Views
    731

    RE: ZDZ80 Prop Nut and Bolts

    reduce torque, so the wood is not compressed all the way beyond the amount it can resist. Get a feel about the needed torque, and after that, check the bolts for tightness often.
    Light coloured...
  13. Replies
    29
    Views
    1,795

    RE: after run?

    ATF for me as well.
    for after run oil
    for machining aluminum
    for general oiling purposes
    for anti-corrosion coatings
    for tapping threads
    nothing left for my car? Heck, it's Europe, I have...
  14. Replies
    5
    Views
    1,603

    RE: Castor Oil Synthetic vs Natural

    You should get your results in these threads
  15. Replies
    6
    Views
    1,346

    RE: walbro HDC carb question

    That screen looks like a capillary screen that will not flow fuel or air until certain conditions are met and the wet seal breaks. A device like that normally is used either as non-return valve in...
  16. Replies
    48
    Views
    3,616

    RE: Proper Throttles on Gas Engines

    at one time, mvvs sold their 26cc engine with ball link fitted.
    Too many people complained it was not the right size ball, so in the end they removed the item.:D
  17. Replies
    29
    Views
    2,741

    RE: 20cc rear carb engine

    Oh Boy! How wrong I was.
    The engine looks nice. How does it run?
  18. Replies
    3
    Views
    494

    RE: Evolution 26cc muffler question

    If you want more detailed info, why not contact Horizon?
  19. Replies
    6
    Views
    1,346

    RE: walbro HDC carb question

    very exciting! :-)
    from the walbro site:

    Part Name HDC-44-1
    Venturi (mm) 11.13
    * Kit - Repair K10-HDC
    ** Kit - Gasket/Diaphragm D10-HDC
    1 * Ring - Screen Retainer 16-42...
  20. Replies
    3
    Views
    494

    RE: Evolution 26cc muffler question

    you will loose power. Check out www.mvvs.cz for rpm loss with different mufflers.
  21. Replies
    6
    Views
    1,346

    RE: walbro HDC carb question

    check out http://wem.walbro.com/walbro/family2.asp , and find out all about your carb.
    The inner screen filter is the carbs last defense to hamfisted users. It should be clean. If any dirt ever is...
  22. Replies
    29
    Views
    2,741

    RE: 20cc rear carb engine

    decent rear carb 20cc?? not likely to happen soon at a decent price. 20cc is still the realm for glow engines, so at best you could see a glow engine-like gas engine with front carb, so it can do...
  23. Replies
    9
    Views
    761

    RE: low speed adjustment on OS7D carb

    I do not have the carb available any more, but |If i recall well, the main needle and idle needle were quite standard. The non-standard part is the midrange adjustment. So run your engine at...
  24. Replies
    3
    Views
    1,013

    RE: Flex Header Repair

    The teflon tape, a normal plumbing grade, serves to prevent the flex header from leaking. Tightly wrap a few layers. Degrease the flex part before you do.
  25. Replies
    2
    Views
    2,788

    RE: MVVS 26 IFS SP

    Amen to that.
    I do know of people that run 10,000 rpm, but then the header needs to be about one inch shorter.
    16x8 is too small a prop.
    18x6 to18x10 is what the engine likes best, using the...
Results 1 to 25 of 1000
Page 1 of 40 1 2 3 4
All times are GMT -6. The time now is 09:47 AM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.