Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: Ybenjulkay2x

Page 1 of 26 1 2 3 4

Search: Search took 0.96 seconds.

  1. Replies
    5
    Views
    394

    have you flew one before?. Best also to...

    have you flew one before?.
    Best also to purchase a simulator and practice a lot on simulator
    before flying the hk 450.
  2. Replies
    5
    Views
    211

    pending means sometimes they are out of stock....

    pending means sometimes they are out of stock. happen to me a lot when ordering lipo batt for heli.
  3. Replies
    12
    Views
    287

    you are running lean due to air leak on fuel line...

    you are running lean due to air leak on fuel line or tank it self, try to do bubble test on both tank and line.
    use a gal container filled with water, dip you tank with one fuel line connected, plug...
  4. Replies
    6
    Views
    209

    it says HIROBO Brand at the fly bar?

    it says HIROBO Brand at the fly bar?
  5. Replies
    2
    Views
    455

    I could tell your pitch adjustment is out, do you...

    I could tell your pitch adjustment is out, do you have a pitch gauge?
    Disconnect the motor, set your radio to center stick then check your pitch supposed to be zero
    on high +10, on low -10.
    Also...
  6. Replies
    8
    Views
    225

    before you go to collective pitch type get a...

    before you go to collective pitch type get a simulator first if you crash just reset it then fly again instead of wasting lot of money for repair.
    It happen to me when I got a CP axe from heli max...
  7. Thread: Hpi .25

    by Ybenjulkay2x
    Replies
    7
    Views
    150

    Do you have suggestions on how to break in...

    Do you have suggestions on how to break in properly I do not have a manual I bought it off ebay
    Run it reach for @ least a gal or two, lot of smoke. If it's hard to turn use hair dryer to heat up...
  8. Replies
    8
    Views
    190

    I love all the RC stuff I build last time till...

    I love all the RC stuff I build last time till the RTR come.
    Start on the old school day RC10 tub (gold)type, BMT 931 to 1/8, the old Serpent impact 1/10 to M3 ,Ofna Colt 1/10 and 1/8 to Mugen 1/10...
  9. Thread: Hpi .25

    by Ybenjulkay2x
    Replies
    7
    Views
    150

    The .25 is it pull start type engine or not? It...

    The .25 is it pull start type engine or not?
    It is normal for a new engine to turn hard due to the tightness of the piston and sleeve
    use hair dry dryer to heat up the engine to loosen it up...
  10. yeah that's right pure ten it's been a while,...

    yeah that's right pure ten
    it's been a while, maybe 10 years ago
  11. ReaDY2Roll mention it's Kyosho

    ReaDY2Roll mention it's Kyosho
  12. There's another story I've just read on the news...

    There's another story I've just read on the news that happens in NY city.
    This one kid flying his heli I believe he's using align 700, the heli went out of control
    and the heli went toward and and...
  13. Replies
    1
    Views
    110

    maybe some few things need to adjust. 1st. it...

    maybe some few things need to adjust.
    1st. it need to speed up a little bit, turn your high end 1/16 turn, check your engine temp if less than 260 F first. Or
    2nd . you may adjust (loosen 1/8 turn)...
  14. well one of the worst night mare I have when my...

    well one of the worst night mare I have when my 450 crash, it crash due to gusty wind, wind picks up, the worst thing is it crash on the bushes, before I found the heli, the battery flame on, after a...
  15. Replies
    2
    Views
    124

    As I could remember I have one of that ESC...

    As I could remember I have one of that ESC before, to enter you need to lower the throttle stick.
    Check the setting of your radio th setting, low need to be 0.
    to initiate th up then plug ur...
  16. Check the belt maybe loose or a bad tail shaft...

    Check the belt maybe loose or a bad tail shaft pulley (pulley slip from the shaft) or maybe the
    main gear screw missing (screw holding the main gear to main shaft)
  17. I'm not familiar how to set JR radio also you...

    I'm not familiar how to set JR radio also you also need pitch gauge to set your pitch curve.
    ex setting pitch curve.......................T up 0/50/100
    ...
  18. I believed it's the Super 10 GP from Kyosho

    I believed it's the Super 10 GP from Kyosho
  19. first what type radio you got

    first what type radio you got
  20. Replies
    9
    Views
    434

    RE: Seating a new spur gear

    if your not sure how much your gear mesh, use the paper technique.
  21. Replies
    26
    Views
    938

    RE: can't go full throttle

    Try reachin it up half turn and see.
    As I remember I encounter this problem on my MRX-3 with an RB S7C I beleive (engine still alive in my MRX-3),
    as fuel almost reach half tank engine start to...
  22. RE: Engine Problem for ECX Revenge Type N Nitro

    It sounds like U still have a reach HSN setting, try this when engine start, pinch the carb fuel line if it dies right away ur high end is lean, if engine stay more than 5 second
    ur high end is...
  23. Replies
    26
    Views
    938

    RE: can't go full throttle

    By the way what type of plug ur using, Hot, Medium, Cold?
  24. Replies
    26
    Views
    938

    RE: can't go full throttle

    I you have an extra fuel line (clean), attach one end line to the tank (tank to carb), with your finger holding the other hole (tune pipe to tank), submarge the
    fuel tank to a gallon (example) of...
  25. Replies
    26
    Views
    938

    RE: can't go full throttle

    [quote]ORIGINAL: dawg242

    *(I have a Cen. .30 engine in my Cen. C1 Matrix 1/8 scale buggy. It starts right up runs like a champ until I go full throttle, then it dies. I've shortend my fuel...
Results 1 to 25 of 629
Page 1 of 26 1 2 3 4
All times are GMT -6. The time now is 09:56 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.