Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: Next edition

Page 1 of 5 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    2
    Views
    110

    Is it hooked upto motor and reciever.

    Is it hooked upto motor and reciever.
  2. Replies
    15
    Views
    503

    Theyre pretty good as is so long as you dont jump...

    Theyre pretty good as is so long as you dont jump them to big and snap a arms and stuff.

    ive done what you want to do aswell put a xerun 150a esc and mamba monster 2200kv and a toro x8st 2000kv on...
  3. Replies
    12
    Views
    254

    You dont wrap the screw you push the tape in the...

    You dont wrap the screw you push the tape in the hole with the 2 ends of tape coming out of it held with youre fingers then put the screw in,you can drape more in there too if its a bigger thread...
  4. only highlighting words instead of the big...

    only highlighting words instead of the big description like this,which is 2800watts at 23volts 121amp draw 45,000rpm max.
  5. Ive used the mamba monster(tork...

    Ive used the mamba monster(tork version)2200kv-hobbywing 2250 but the toro 42/75 2000kv x8st sensored motor I used was the best it has a fan inside the motor on its endbell and ran way cooler and...
  6. Replies
    12
    Views
    254

    2 drips 1 down the hole and 1 on the screw and...

    2 drips 1 down the hole and 1 on the screw and then just smear it over the thread plumbers tape works good too.
  7. Try putting a fan on the motor,on and off...

    Try putting a fan on the motor,on and off throttle alot can cause it to heat up quick.
  8. Replies
    5
    Views
    114

    I think theyre a ezrun 60a esc.if it doesnt sound...

    I think theyre a ezrun 60a esc.if it doesnt sound beeps you might have to watch the flashes.
  9. Replies
    11
    Views
    265

    Does your lhs have traxxas spurs you maybe able...

    Does your lhs have traxxas spurs you maybe able to fit one of those in take it there and compare there dimensions.

    might have to drill the shaft hole out and make the slot a little bigger but it...
  10. Replies
    4
    Views
    121

    You can use a shifting spanner for that nut Or...

    You can use a shifting spanner for that nut Or try the four way wrenches for rc vehicles if youve got one.

    Firms good so if you hold youre truck still on the ground and turn the spur when youve...
  11. Replies
    9
    Views
    306

    [QUOTE=chevymanmike1010;11802648]Well I've...

    [QUOTE=chevymanmike1010;11802648]Well I've changed my mind haha ima go with the hpi blitz 109326 with a 3s lipo.[/QUOTE
    Hpi all the way.
  12. Replies
    2
    Views
    1,166

    Wow they look like very well crafted pieces of...

    Wow they look like very well crafted pieces of art.
  13. Replies
    4
    Views
    121

    Tighten the nut on the slipper clutch where the...

    Tighten the nut on the slipper clutch where the spring is you can go pretty firm on them because its all steel gearing in the tranny.
  14. Replies
    13
    Views
    254

    The higher the c rating is like a fire hose with...

    The higher the c rating is like a fire hose with the tap turned up or down,its going to give more punch,in our racing meets we all use 60 plus c rates 80 is one of the highest ive used.
  15. I ran 106mph on a hpi firestorm with 2.2 tyres on...

    I ran 106mph on a hpi firestorm with 2.2 tyres on the front and foams on the back the front was lowered and back slightly elevated mod1 gearing 31/34t pin/spur xerun 150a esc and torox8st sensored...
  16. Replies
    2
    Views
    350

    Was going to say a rustler is more than capable...

    Was going to say a rustler is more than capable of that and coulda maybe got it cheaper second hand youtube 100mph rustler.
  17. See if you can put the pinion on the spur shaft...

    See if you can put the pinion on the spur shaft if so you can get a 30-40 steel pinion and use that for a spur.

    you may have to custom mod it to fit because im not sure how it locks in place...
  18. Block the carb intake with your hand and rotate...

    Block the carb intake with your hand and rotate the crank and let it suck and stick to your hand and see if it sticks if you hold it off the bench a little if it stays stuck compresions good if it...
  19. Xerun 150a and toro x8st sensored 2000kv ive used...

    Xerun 150a and toro x8st sensored 2000kv ive used the mamba monster combo 2200 kv and xerun combo and the toro was better for all out grunt and much cooler temps and was the cheapest aswell alot of...
  20. Compression check,no air leaks.

    Compression check,no air leaks.
  21. Sticky: Rampage elite-rampage covert.

    Rampage elite-rampage covert.
  22. Replies
    1
    Views
    137

    No its got a centrifugal clutch on its crank end...

    No its got a centrifugal clutch on its crank end where the gearing is if its worn it will take alot of throttle to get it going if its faulty it will basically take off as soon as you start it up and...
  23. Thread: foams

    by Next edition
    Replies
    11
    Views
    141

    What about a soldering iron with a different tip...

    What about a soldering iron with a different tip and burning in profiles.
  24. Replies
    4
    Views
    249

    Look into what theyre using seems quite low...

    Look into what theyre using seems quite low geared try a bigger pinion like a 20t,I get what you mean by quiet which is why im registered with ultimaterc and rctech aswell so then you can ask on all...
  25. Replies
    19
    Views
    435

    Save youre money and buy a second hand roller and...

    Save youre money and buy a second hand roller and new elecs,I like 2wd hpi firestorm-rustler because ive never broken anything and thats running them over 80mph plus and makes for a challenge trying...
Results 1 to 25 of 108
Page 1 of 5 1 2 3 4
All times are GMT -6. The time now is 03:46 AM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.