Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: karolh

Page 1 of 40 1 2 3 4

Search: Search took 1.90 seconds.

  1. Replies
    1,904
    Views
    193,557

    The section of the engine that needs cooling most...

    The section of the engine that needs cooling most is the cylinder and ideally one should try to direct incoming air in and around the cylinder fins. The other area of major concern is getting rid of...
  2. Replies
    5
    Views
    152

    Exactly.

    Exactly.
  3. Replies
    126
    Views
    5,875

    Subs.

    Subs.
  4. Replies
    2
    Views
    106

    Either of your chargers can be used to charge...

    Either of your chargers can be used to charge your battery and unlike charging Nicads a Lipo, does not have to get warm to be fully charged. Most times when Lipos start showing signs of puffing...
  5. Replies
    5
    Views
    152

    Balancing a Model

    Is there any real difference in balancing a model right side up versus balancing it upside down.
  6. Replies
    9
    Views
    171

    Since my right hand came in contact with a 14"...

    Since my right hand came in contact with a 14" APC prop that was vigorously defending it's air space a few years ago I have gone exclusively to using wood props.
  7. Replies
    9
    Views
    171

    Went flying today and a Xoar 16x6 seemed to...

    Went flying today and a Xoar 16x6 seemed to perform just a bit better than the 17x6
  8. Replies
    9
    Views
    171

    Best size prop for a Zenoah G20.

    What size prop works best for general sport flying on a Zenoah G20 engine.
  9. Replies
    11
    Views
    297

    I once tried using some TP 5010's and found them...

    I once tried using some TP 5010's and found them to be quite coarse and jerky in their movement, plus there are much better quality budget priced servos available such as Savox or Solar. Not because...
  10. Replies
    6,728
    Views
    809,385

    Sounds like you are a bit lean on the HS needle.

    Sounds like you are a bit lean on the HS needle.
  11. Replies
    1,577
    Views
    138,619

    It's pretty much up to the builder regarding...

    It's pretty much up to the builder regarding covering the tail feathers before gluing them to the fuse, but for me I prefer to cover them first as they are a lot easier to handle. As for the distance...
  12. Would appreciate you sharing your findings with...

    Would appreciate you sharing your findings with us regarding the performance difference between the 16x8 and the 17x6 props. Both Jody and Pat advised while they were still here that for engines 30cc...
  13. My M22 powers a scratch built 63" span Extra...

    My M22 powers a scratch built 63" span Extra profile and on an 8 oz tank spinning a Falcon 17x6 runs close to 20 mins with a bit left in the tank, but then I hardly ever run full throttle except when...
  14. Great that you are again enjoying your engine, as...

    Great that you are again enjoying your engine, as I plan on doing some of the same with mine very soon. How much fuel have you ran through yours since returning it to active duty ?? Sent you a...
  15. I have always used RC 56 for gluing on canopies...

    I have always used RC 56 for gluing on canopies and I have never had one come loose, while venting the canopy via a small hole in the cockpit floor is a much easier way to go.
  16. Good for you as there is nothing quite like a...

    Good for you as there is nothing quite like a sweet running engine to bring a smile to one's face.
  17. Hey Capt,n John, what's the latest on your Mintor...

    Hey Capt,n John, what's the latest on your Mintor 22 and guess what, mine is finally home at last but I have not had the chance to run it just yet. Will post something as soon as I do.
  18. Replies
    35
    Views
    1,966

    Two very nice looking models.... great job.

    Two very nice looking models.... great job.
  19. Thread: Value Hobby?

    by karolh
    Replies
    50
    Views
    1,788

    I second that.

    I second that.
  20. Thread: Value Hobby?

    by karolh
    Replies
    50
    Views
    1,788

    Several of my friends and myself have made...

    Several of my friends and myself have made numerous purchases from VH as they offer fairly good products at very reasonable prices, and so far we have never any problems with the items purchased or...
  21. Replies
    192
    Views
    15,039

    My all time favourite is a ST .60 Blue head, now...

    My all time favourite is a ST .60 Blue head, now fitted with a FB ring still runs like a top.... closest thing to perfection.
  22. Replies
    878
    Views
    88,489

    I would suggest that you make a wood spacer of...

    I would suggest that you make a wood spacer of equal thickness as the desired extension you need and securely fix it to the model's existing firewall and use a standard aluminium engine mount (as...
  23. Replies
    25
    Views
    367

    Zenoah engines like to rev so don't go over...

    Zenoah engines like to rev so don't go over propping them. On my G23 I use Xoar 16x8 or a 17x6 if I have sufficient ground clearance, both of which the engine performs well with.
  24. Turnigy Accucell 8150 charger backlight not working.

    The backlight on my Accucell 8150 charger has stopped working, however everything else works. Does anyone know of a possible fix like a backlight chip replacement. Thanks.
  25. Replies
    11
    Views
    673

    It's my guess that he was in hybernation and just...

    It's my guess that he was in hybernation and just woke up.... :p
Results 1 to 25 of 1000
Page 1 of 40 1 2 3 4
All times are GMT -6. The time now is 12:08 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.