Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: breadmantripp

Search: Search took 0.04 seconds.

  1. Replies
    1
    Views
    64

    Engine probs

    I can get the engine 2 start but only after the fuel has sat in engine for lets say 10 min. Once I get it to start it seems as if the idle is very high and once I apply full throttle it cuts out and...
  2. Replies
    3
    Views
    75

    Already did it, that wasn't the problem

    Already did it, that wasn't the problem
  3. Replies
    3
    Views
    75

    Wheel stops spinning

    On my 1/36 losi micro t I pull in on the throttle with the wheels off the ground both tires start spinning but one eventually stops spinning while other keeps goin. Anybody have any clue what goin on...
  4. Replies
    7
    Views
    231

    Done it. We start very loose, then tighten till...

    Done it. We start very loose, then tighten till it till we finally have the right amount of slip. The motor mount is pushed all the way over or it won't mesh properly, I'll have 2 post some pics or...
  5. Replies
    7
    Views
    231

    Seriously, I about can't take it anymore. Went...

    Seriously, I about can't take it anymore. Went back 2 the metal spur gear but started chipping the bell, which is why I quit using the metal, but my plastic spur gears last about 5 times around the...
  6. Replies
    7
    Views
    231

    Now it's my spur gear, keep stripping the gear. I...

    Now it's my spur gear, keep stripping the gear. I kno the mesh is fine. Can't fig out why this keeps happening? I bash my traxxas jus as much mayb even more, and no probs this yr. I just can't figure...
  7. Replies
    1
    Views
    162

    Should I throw it away?

    I'm guessing most of u will say yes but here it goes anyway. I bought a redcat backdraft 3.5 last yr cuz I wanted my dad 2 get n2 rc with me. I was new 2 the hobby and just wanted 2 get the least...
  8. Replies
    7
    Views
    231

    I need better parts

    Keep stripping thread on servo saver on my backdraft 3.5, need 2 kno if any1 has used another company's servo saver? Or if any of the hop up parts for other redcat cars will work on the backdraft...
  9. I did loosen them already, but it was that nut on...

    I did loosen them already, but it was that nut on top of the left post of the servo saver. I had 2 tighten it. I basically rebuilt the car due 2 the chasis was bent. I had purchased the upgraded...
  10. I'm thinking it has something 2 do w/ the servo...

    I'm thinking it has something 2 do w/ the servo saver. Mayb the bolt that screws into the top of one of the posts on the saver? I'm messing around w/ it right now but nothing has seemed to work yet
  11. Sorry I probably should of said it was a backdraft

    Sorry I probably should of said it was a backdraft
  12. This is not a tornado, it's a backdraft 3.5. I...

    This is not a tornado, it's a backdraft 3.5. I put a tactic 2.4 transmitter/reciever in it. I have a steering trim and steering rate knob, also a throttle trim.
  13. Bringing back an old post because what happened...

    Bringing back an old post because what happened to him is happening 2 me but it has nothing to do with end points, steering trim or servo's. Can't figure out why I can only turn the car just the...
  14. Replies
    2
    Views
    123

    Did I break my diff

    Rolled my backdraft 3.5 real good 2day. Checked it out cause it went flyin end over end a couple times. Every thing looked good but when I gave it a push while it wasn't running 2 see if it rolled...
  15. Replies
    1
    Views
    108

    Backdraft 3.5 tranny

    I have the toughest time getting the transmission to shift into 2nd, can't get it to do it. 1st n the video's it says there are 2 screws located inside the tranny when in fact there is only 1. Second...
Results 1 to 15 of 15
All times are GMT -6. The time now is 08:34 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.