Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: Tony Hallo

Page 1 of 40 1 2 3 4

Search: Search took 1.36 seconds.

  1. Replies
    7
    Views
    569

    Four stokes use pulses in the intake for pump...

    Four stokes use pulses in the intake for pump action, much weaker the two stroke crankcase pulse pressure. Some uses have installed electric pumps to cure their problems.
  2. Replies
    4
    Views
    203

    I thought there are keys installed? At least the...

    I thought there are keys installed? At least the ones I worked on, G62 and GT80. The G26 uses the same mag, different magnet. If you do not prop through both magnets it will pop as stated, read...
  3. Replies
    123
    Views
    6,358

    Attached are a few shots of the finished flying...

    Attached are a few shots of the finished flying wires. The ends are made as previously discuss. The wire is from Pro Bass shop in Myrtle Beach SC in the salt water section. I bought a fancy...
  4. The plans provided no additional detail to the...

    The plans provided no additional detail to the gear other what is shown below
  5. Attached is the build article.

    Attached is the build article.
  6. Fiberglass Specialties lists the parts...

    Fiberglass Specialties lists the parts http://www.fiberglassspecialtiesinc.com/catalog.htm. The time was early 1988-1991 time frame. Long before the internet was invented by Al Gore.
  7. I believe that plane was built around the TR260...

    I believe that plane was built around the TR260 plans from Model Builder magazine. I would check with T-N-T landing gear they may have the dimensions already. I built three or four of these from...
  8. Replies
    123
    Views
    6,358

    HP Matt Did you get the PM? It is unclear if it...

    HP Matt
    Did you get the PM? It is unclear if it sent or not.
  9. Replies
    7
    Views
    259

    I can't image you will get a reliable idle...

    I can't image you will get a reliable idle without a prop or flywheel installed.
  10. Replies
    123
    Views
    6,358

    I assume it is lockable, do you control this from...

    I assume it is lockable, do you control this from the cockpit? Looks like an old tail wheel was remove?
  11. Replies
    7
    Views
    259

    Is there a flywheel installed? Would think might...

    Is there a flywheel installed? Would think might help smooth thing out
  12. Replies
    123
    Views
    6,358

    I just didn't like the looks of the J&J Tail...

    I just didn't like the looks of the J&J Tail wheel although is made beautifully. I first cut off the horns and finished off the sides on disc sander, still did like it. I then decided to modify the...
  13. Replies
    107
    Views
    8,751

    What table are you asking about?

    What table are you asking about?
  14. Replies
    2
    Views
    122

    I built my own on my own ...

    I built my own on my own http://www.rcuniverse.com/forum/giant-scale-aircraft-general-467/11232686-rc-guys-cherokee-140-revamp.html . Used these on the rudder and ailerons. They work fine and look...
  15. Replies
    3
    Views
    200

    Devin, Attached are photos of the cowl. As I...

    Devin,
    Attached are photos of the cowl. As I stated I had filled the holes cut by the original owner to make the plaster mold.
  16. Replies
    3
    Views
    200

    Devin I'll trade you a set of the One design for...

    Devin
    I'll trade you a set of the One design for the 40% Laser plans.
  17. Replies
    123
    Views
    6,358

    I began covering the fuselage, the white color...

    I began covering the fuselage, the white color covering is all one piece. The covering shrinks so well it was easy doing it in one piece. I was able to iron the green over top without any Windex. ...
  18. Replies
    123
    Views
    6,358

    I am not sure if the rudder will be a push rod or...

    I am not sure if the rudder will be a push rod or a '"pull-pull" set up. I have the rails installed for the elevator servo already, these were glued to the sides before they were jointed, the rudder...
  19. Replies
    123
    Views
    6,358

    I pulled the trigger on the remainder of the...

    I pulled the trigger on the remainder of the servos yesterday. Hobby King had a sale on most items. I was surprised to find these...
  20. Replies
    123
    Views
    6,358

    The fuel tank is a 20 ounce water bottle. For...

    The fuel tank is a 20 ounce water bottle. For the tube connections, I soldered 5/32" K&S tubing to a .025" copper plate and drilled the original cap for the tubes to exit. The bottle to plate joint...
  21. Replies
    38
    Views
    2,052

    Please let me know if you find a source.

    Please let me know if you find a source.
  22. Replies
    8
    Views
    273

    Looks like you will have plenty of throw, how...

    Looks like you will have plenty of throw, how many degrees are you looking for?
  23. Replies
    74
    Views
    7,181

    The kit as made in the day when lasers and CNC...

    The kit as made in the day when lasers and CNC were new and expensive technology, the use of such would have resulted in kit cost outside the norm that nobody would buy. That coupled with other...
  24. Replies
    123
    Views
    6,358

    I mocked up the wire attachment below. The nylon...

    I mocked up the wire attachment below. The nylon clevis needs a piece of tubing to keep closed under high stress, the #2 screw is better for this application. The hole side is drilled for clearance...
  25. Replies
    123
    Views
    6,358

    The exhaust is silver soldered together, the...

    The exhaust is silver soldered together, the black flux seemed to work better than the white, cleaned better while soldering and afterwards. The label states it is for stainless so I expect that is...
Results 1 to 25 of 1000
Page 1 of 40 1 2 3 4
All times are GMT -6. The time now is 09:24 AM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.