Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: westoakmech

Search: Search took 0.14 seconds.

  1. Replies
    0
    Views
    356

    Hobby shop in Stillwater OK

    Hello does anyone know if there is a hobby shop still open in Stillwater OK. About a year ago there was a guy on here asking about becoming a redcat dealer there. I am going there this weekend and...
  2. RE: Davis Model Products Heavy Duty Rod Traxxas 2.5/3.3

    I have run one. Not all that impressed with it, it does the job, is a little heavier, did not notice any real performance loss from the weight.  My problem was that after about five gallons, the...
  3. Replies
    1
    Views
    211

    RE: 2.2

    You can run gladiators, they are larger square pins. You could also look into bad lands. Both are pro line. The bad lands may only be available in 2.8.
  4. Replies
    3
    Views
    289

    RE: 3.3 slipper for 2.5 Maxx

    The only down fall to running that kit is I think there is only the one gear 72t that will work with it. It looks like the same spur gear, but it has a concave in it, so the others will not work. If...
  5. Replies
    3
    Views
    692

    RE: E Revo issues

    The stock traxxas servo for the 1/16 is notorious for going bad and doing just that. Did you buy the servo? or did it come with the car? It may have been bad already. I am running a hitec metal...
  6. RE: serious issue with t-maxx 3.3 please help

    It could have pulled the ears off from the bottom of the piston, where the wrist pin goes though. It will still have some compression, but not enough. I had that happen on a 2.5 that over sped. I...
  7. Replies
    2
    Views
    334

    RE: T-Maxx 2.5 take it or leave it?

    Looks like a pro .15 engine, also looks like it is missing two front shocks. Also looks to be reverse trans, with no servo. Looks really clean though, For around a $ 105 you could buy a 2.5r engine...
  8. RE: How to install a .28 nitro engine on a traxxas 3.3 tmaxx

    I have not ever done it. But I know that you would for sure at least need a chasis extension, and a big block mount. Other than that I can be of much help to you. Good luck
  9. RE: ECX Smash - questions about brushless upgrade

    Yes punch control wil reduce how hard it hits on take off, kinda like a delay. I think, if remember correct the higher the number the more punch control.
  10. RE: ECX Smash - questions about brushless upgrade

    If you gear it low it enough it will probably stil wheelie. Also will depend on battery selection. A 2s lipo will be more likely to wheelie than a nihm. I have the smash also, got it for my daughter....
  11. Replies
    15
    Views
    558

    RE: Best Gearing

    According to traxxas, the stock pinion on your ride is a 23 tooth. They show all the way down to a 16. You could drop a couple of teeth at a time, and see if that gets you were you want to be. My...
  12. Replies
    22
    Views
    1,787

    RE: 3.3 LIFE SPAN

    I run the davis rod in my 3.3, no problems.
  13. Replies
    24
    Views
    3,216

    RE: Redcat 1/16 Tremor models

    It looks alot like a little bigger sumo. The tires do look just like the summit.
  14. Replies
    8
    Views
    717

    RE: Tornado EPX Pro run times

    I also bought my son the tornado for x-mas. The lipo low voltage turned on. I used the program card and shut it off. It also came back on by itself and I had to shut it off again. He gets between 15...
Results 1 to 14 of 14
All times are GMT -6. The time now is 11:52 AM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.