Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: ShredderGuy

Page 1 of 3 1 2 3

Search: Search took 0.18 seconds.

  1. Replies
    18
    Views
    980

    RE: problem with steering linkage

    Use some loctite on it. It won't come lose them.
  2. Replies
    3
    Views
    698

    RE: HOLY CRAP

    I run same thing on my Volcano EPX Pro. It is a damn wheelie monster even with the punch down.
  3. Replies
    4
    Views
    463

    RE: Newbie getting started

    Do all the above mentioned and also take a hair dryer to it and pre-warm the motor. It will be easier to pull and will start quicker.
  4. RE: Single vs. 2 Speed? Anyone plz help??

    In my experience a single speed is best for a nitro beginer hobbiest. They are easier to maintain and tune.

    They problem with a lot of two speeds is 1, ) the motor has to be tuned spot on for it...
  5. RE: How many Aftershock 8E's needed for a good bash?

    These are meant for a bit of everything. You can bash them, race them, and pretty much drive them without issue on any terrain.
    <br type="_moz" />
  6. Replies
    8
    Views
    524

    RE: Backdraft vs Hurricane?

    If you do not want problems.. Buy the Hurricane XTE. It is a Beast!
  7. Replies
    5
    Views
    453

    RE: caldera 10e

    There is a video on youtube of a guy doing a NIMH speed test and a Lipo Speed test on his Caldera 10E Stock it was like 19MPH, Lipo was 42MPH or so. I looked for the video but I could not find it....
  8. RE: So I ordered my wife a Volcano EPX Pro

    Yep, I already have a program card I purchased from Redcatracingshop.com a while back. I am going to change some setting in it when it is a little nicer out and the truck can acutally be used.
  9. Replies
    0
    Views
    190

    Easy Connector For Dual Lipo's?

    Anyone know of a 4mm Bullet connector you could hook into your ESC that would be set up to run dual lipo's? I looked around for a while and did not fine one. I did not want to have to solder and make...
  10. Replies
    8
    Views
    430

    RE: Alignment on Caldera 10e

    Unhook your steering servo horn and make sure the servo is set to neutral then hook it back up with your wheels straight. Here is a quick how to video I found on youtube for you. I did not watch it...
  11. So I ordered my wife a Volcano EPX Pro

    On Monday I ordered my wife a Volcano EPX Pro from Redcat Racing Shop. I got that a Thunder AC6 Charger and a 5000MAH 2S Lipo. All I have to say is sweet mother of god, that thing is stupid fast.
    ...
  12. Replies
    5
    Views
    560

    RE: redcats not starting

    Just put a glow plug in the end of your glow ignitor and see if it lights up. If it does your glow plug is good and so is your ignitor.
  13. Replies
    6
    Views
    528

    RE: Best place to buy parts/upgrades

    It's no problem. I just feel obligated to plug that shop when I can since he gave me such great deals when I bought my Shredder.
  14. Replies
    6
    Views
    528

    RE: Best place to buy parts/upgrades

    I buy all mine from www.redcatracingshop.com
  15. RE: What size of screw or part number do I need?

    I guess it's only money right? Hahaha.
  16. RE: What size of screw or part number do I need?

    Yeah, I looked at the schematic and that screw is not listed as a part numer. I will have to call Redcat tomorrow I guess.
  17. What size of screw or part number do I need?

    I lost a screw that goes from the front lower control arm into the steering knuckle on my Shredder. I purchased every screw I could basically find for the shredder and none of them are it.

    I was...
  18. RE: Bent screws on Calders 10e steering arms keep occuring????

    I just go to the hardware store and buy hardened screws for mine. If I can't find them I usually just order like a pack of 10 or however they come from a Redcat Dealer.
  19. RE: What lipo are you running with caldera 10e and or Hurricane or Avalanch?

    I will put a GPS on it and we will find out.. The snow should be gone off the ground by this weekend.
  20. RE: What lipo are you running with caldera 10e and or Hurricane or Avalanch?

    I Upgraded to this ESCin my Shredder XT. It comes with the same ESC/Motor combo that the XTE series does. I currently run two 5000MAH 3S Lipo's on it and it is CRAZY FAST! (I never thought I would...
  21. Replies
    4
    Views
    434

    RE: New Volcano S30

    This is what I upgraded to.

    http://www.redcatracingshop.com/product_p/79p-gt3b-carradio-lcd.htm

    It is not a great upgrade but I have had that RX/TX for about a year with no problems. I also...
  22. RE: Can Caldera 10e and Hurricane xte take 3-4 cell lipos?

    Nice collection. If I would have kep all my RC's over the years they would fill my garage.

    But those run times are based on my shredder which is the same thing on an extended chassis.
    <br...
  23. Replies
    4
    Views
    434

    RE: New Volcano S30

    I have not heard of a real problem with the radio's like this. Did you try to re-bind the TX/RX? That may take care of it. If it doesn't I would guess you have a bad RX. I would not even replace it...
  24. RE: Can Caldera 10e and Hurricane xte take 3-4 cell lipos?

    Stock runtime will only be 12 - 15 minutes depending on driving style. With dual 5800's you should see a 25 min + run time.
  25. RE: Can Caldera 10e and Hurricane xte take 3-4 cell lipos?

    I bought thisESCfor my shredder and I run dual 3S 5000MAH lipo's on my stock motor. I just watch the temps and it has treated me well so far. Not to mention I picked up atleast 10 MPH more easy.
Results 1 to 25 of 55
Page 1 of 3 1 2 3
All times are GMT -6. The time now is 07:42 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.