Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: Jim Branaum

Page 1 of 40 1 2 3 4

Search: Search took 0.85 seconds.

  1. Replies
    8
    Views
    183

    Well, I guess they did not have it since they...

    Well, I guess they did not have it since they only shipped the WT-76. However, I found one at...
  2. Replies
    8
    Views
    183

    I assume it is new. http://tewarehouse.com/ ...

    I assume it is new. http://tewarehouse.com/ Ordered the one for the 3W and a WT-76 for my BME total with shipping less than $130.

    If it is not new when it gets here, I will post accordingly.
  3. Replies
    8
    Views
    183

    Thanks guys, ordering a CARB WALBRO SDC80 P61 (W)

    Thanks guys, ordering a CARB WALBRO SDC80 P61 (W)
  4. Replies
    8
    Views
    183

    Correct carb for older 3W-75

    Kids can be a real PITA when they are playing where they shouldn't be with stuff they are not supposed to touch. :(

    I took the carb off the engine, disassembled it, soaked it, dried it out, and...
  5. Replies
    60
    Views
    2,014

    I have been considering something kind of like...

    I have been considering something kind of like that as a home for my BME 44....
  6. Replies
    93
    Views
    5,172

    Hmm... It seems to me that if one is committed...

    Hmm...

    It seems to me that if one is committed to flying RC one should be willing to travel to where peers and friends can be found. My club's nearest field is ~35 miles from my home and the main...
  7. Replies
    122
    Views
    6,273

    But it WORKS! :cool:

    But it WORKS! :cool:
  8. While I am using a slightly different (read that...

    While I am using a slightly different (read that as cheaper) system, the hint about screws is on target. I put 1/2 electrical pipe into 2x4 (upright fastened to the trailer) drilled (11/16 and then)...
  9. Replies
    12
    Views
    261

    Sent you a note.

    Sent you a note.
  10. Replies
    12
    Views
    261

    Darn. I would have been extremely interested...

    Darn. I would have been extremely interested before I sent the engine in. Now it will just be a good back up as I pulled the sensor before I shipped the engine. PM me details please.
  11. Replies
    12
    Views
    261

    No, but thank you very much for following up and...

    No, but thank you very much for following up and asking.

    I have a spare RCXEL module but did not test it as the connector to the Hall sensor is different and I am loathe to fix what is not...
  12. Replies
    81
    Views
    5,207

    Bill, How did this work out? Is it worth the...

    Bill,

    How did this work out? Is it worth the investment of resources (time, supplies, and money)?
  13. Replies
    12
    Views
    748

    Yeah, I know I am late to the party but I was...

    Yeah, I know I am late to the party but I was looking for something on chargers and saw this thread and it caught my interest. Too bad.



    It seems that the above colored statements are only...
  14. Replies
    64
    Views
    3,284

    It appears you are embedding a carbon rod and...

    It appears you are embedding a carbon rod and tube. Or is that a servo wire tube? What are those 3 structures on the bottom of photo #2?

    You and I have a slightly different view of foam wings...
  15. Replies
    64
    Views
    3,284

    Why is this beginning to look like just another...

    Why is this beginning to look like just another oil thread?



    While your question has been answered in several different manners there are other issues to consider. CA is NOT UV resistant. ...
  16. Replies
    12
    Views
    261

    No, I am very careful to install my stuff so it...

    No, I am very careful to install my stuff so it stays clear of the muffler and/or stacks. I have noticed that melted electronics seem to let the magic smoke out. In this case, the exhaust stack...
  17. Replies
    12
    Views
    261

    Oh, I understand that most know more than I would...

    Oh, I understand that most know more than I would hope to but that was one of the very first things we checked because I really like simple answers. :(

    To be a little bit more explicit, I have...
  18. Replies
    12
    Views
    261

    SPE 40 ignition problems

    I have been flying the engine it a Gere Sport all summer. Last weekend I went to an event and the first day, it ran like normal and I was having a blast. Well, until the solder job on the muffler...
  19. Replies
    1,064
    Views
    48,163

    Thanks. It is nice to be airborne again.

    Thanks. It is nice to be airborne again.
  20. Replies
    32
    Views
    1,421

    Lipos have caused grass fires, as have turbine...

    Lipos have caused grass fires, as have turbine crashes where the accelerant is carried to the scene of the hot section broken open. I have not seen a gas fire or a nitro fire, but it is possible.
  21. I wish I had noticed this thread 2 years ago...

    I wish I had noticed this thread 2 years ago before I started on my new 6x12 V nosed trailer! It is not too late to steal some of the ideas, so I will do that.

    My approach is a bit different as...
  22. Replies
    20
    Views
    1,197

    Hmmm... I have a 6X12 V nosed trailer (special...

    Hmmm...

    I have a 6X12 V nosed trailer (special built with a torsion axle - got tired of the old one beating my planes up). To start with the wife insisted I do nothing permanent to it, so I spent...
  23. Replies
    1,064
    Views
    48,163

    I really hate specialized servos like retract...

    I really hate specialized servos like retract servos. Even more so when they go bad. :(

    From my Jpower electric P-38:

    203463920346402034641

    Hopefully you can see that it is about 1 1/4...
  24. Replies
    4,925
    Views
    158,947

    At least you would know at the very beginning...

    At least you would know at the very beginning that it was a keeper....
  25. Replies
    1,245
    Views
    41,276

    Thanks for the picture with the tape. Now I know...

    Thanks for the picture with the tape. Now I know what to build as I bend my own . Congrats on finishing.

    I have been AWOL with my son who was here for 6 weeks before going to Ft Lenard Wood for...
Results 1 to 25 of 1000
Page 1 of 40 1 2 3 4
All times are GMT -6. The time now is 08:31 AM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.