Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: 1QwkSport2.5r

Page 1 of 40 1 2 3 4

Search: Search took 1.06 seconds.

  1. Thanks Dave. Now to become the master fuel...

    Thanks Dave. Now to become the master fuel mixer; making diesel fuel. John Deer starting fluid, kero, castor, and Amsoil ignition improver, right?
  2. Replies
    3,586
    Views
    222,629

    I run regular muffler pressure on all of my...

    I run regular muffler pressure on all of my engines except one or two (no muffler). Some of my Super Tigre, both K&Bs, and my Enya .30 all leak a little fuel from the needle.. My ST S29 is...
  3. You looking to sell one of those .50 heads, Dave?

    You looking to sell one of those .50 heads, Dave?
  4. Replies
    3,586
    Views
    222,629

    Air doesn't leak in. Fuel leaks out at the...

    Air doesn't leak in. Fuel leaks out at the needle valve. Remember the fuel system is pressurized.
  5. Replies
    3,586
    Views
    222,629

    Barring a bad crash, rings and bearings are...

    Barring a bad crash, rings and bearings are readily available. Put a couple Bowman rings on the shelf as spares and run the snot out of it.

    I've not used the new TN carb, and I have not ran...
  6. Replies
    3,586
    Views
    222,629

    H - the Fox parts factory doesn't have any spare...

    H - the Fox parts factory doesn't have any spare parts. Been looking on the auction site for Fox carbs and am coming up empty. I need to .312" carbs for my Twin and I need one for my .46BBRC. ...
  7. Replies
    3,586
    Views
    222,629

    Without getting into plating 101, I've not heard...

    Without getting into plating 101, I've not heard or felt first hand a "tight" nickel plated liner. Brass and aluminum liners, yes. Car engines are notoriously tight and they're all ABC. I...
  8. Replies
    3,586
    Views
    222,629

    My Fox twin feels like that. The ring seal is...

    My Fox twin feels like that. The ring seal is absolutely fantastic - It feels like an ABC. Still not broken in all the way yet either. My ABC Foxes are unrun since the factory test run, so...
  9. Replies
    3,586
    Views
    222,629

    Fox engines aren't notoriously known for being...

    Fox engines aren't notoriously known for being "pretty" anyway... ;)
  10. Replies
    3,586
    Views
    222,629

    I had to offset the muffler aft some because the...

    I had to offset the muffler aft some because the port on the engine is so small and the muffler so large. I had to spend some time with a dremel to shape the adapter to match both ports. I got it...
  11. Replies
    3,586
    Views
    222,629

    I use a TT Pro .46 muffler on my standard .40...

    I use a TT Pro .46 muffler on my standard .40 with a homemade adapter. It needs to be trimmed yet, it's rather ugly (the adapter). Noise is reasonable I think. I have a video posted on the...
  12. Nope, unfortunately. I have some Enya .15's,...

    Nope, unfortunately. I have some Enya .15's, but they're cross flow too.
  13. I'm not gonna mess with the .19 for diesel use. ...

    I'm not gonna mess with the .19 for diesel use. I'll run it on glow. I wouldn't mind dieselizing my .50 though; that's a double ringed piston/steel liner. Should hold up to some torture. I...
  14. Replies
    21
    Views
    1,905

    Same reason Fox engines always get bashed. There...

    Same reason Fox engines always get bashed. There is very little instant satisfaction from an engine built well. I'll guarantee if cared for during a lengthy break in, any well made engine will run...
  15. Replies
    3,586
    Views
    222,629

    Ran the little lapped .40 for a bit today. I...

    Ran the little lapped .40 for a bit today. I didn't have much time to run it but got it dialed in almost perfect in that time. I had to swap the original high speed needle back in; the end was too...
  16. I just realized the Fox .19 can't be converted...

    I just realized the Fox .19 can't be converted unless I had a flat topped piston. The .19rc I have is a baffle piston engine.
  17. Just checked the site, neither of my engines are...

    Just checked the site, neither of my engines are listed on the current list. I'll have to email Davis.
  18. I saw a post from Davis from last year saying...

    I saw a post from Davis from last year saying they had a .19 and a .50 head but I just assumed hey were gone and probably not made anymore.. I'll check into Davis.
  19. I agree with Mr. Cox. Two identical engines...

    I agree with Mr. Cox. Two identical engines side by side will run within a few hundred rpm of one another if the only difference between the two is a bushed crank versus ballraced. Comparing an...
  20. Might be looking for a diesel head or two...

    Got some Fox engines that I hear convert really well and run strong. Got a new Fox .50bbrc and a .19rc that I have considered converting to diesel. Anyone got an idea or two as to where I can find...
  21. Replies
    652
    Views
    12,309

    My special oil is Castor bean oil. I use a...

    My special oil is Castor bean oil. I use a gallon to a gallon and a half a season. It's all I use and will likely continue to do so unless the European stuff drops in price by half of better. :X
  22. Replies
    652
    Views
    12,309

    I use Dawn Power Dissolver too, except I just use...

    I use Dawn Power Dissolver too, except I just use old used toothbrushes with nylon bristles. I don't get too carried away because I'm gonna get it all slimed up again anyway.. ;)

    I got my...
  23. Replies
    21
    Views
    1,905

    Measure the neck size. That is, the ID of the...

    Measure the neck size. That is, the ID of the carb port. That will narrow it down as to what fits. I doubt you want an OEM MDS carb.
  24. Replies
    652
    Views
    12,309

    I doubt it. SIG was selling it for $23/gal and...

    I doubt it. SIG was selling it for $23/gal and last I checked it went up to $38/gal.
  25. Replies
    652
    Views
    12,309

    Gotta love those great deals! The Dykes ringed...

    Gotta love those great deals! The Dykes ringed Irvine .25 Mk II, Fox .19RC, and the Fox .46BBRC ABC I got all NIB for $50 from an estate sale. I mean, $10 for an Irvine .25 almost pristine? Duh! ...
Results 1 to 25 of 1000
Page 1 of 40 1 2 3 4
All times are GMT -6. The time now is 10:46 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.