Search: Posts Made By: GVR-4579
Showing results 1 to 25 of 59
Search took 0.43 seconds.
Forum: Gas Engines
09-01-2014, 02:55 PM
Replies: 6
Views: 456
Posted By GVR-4579

CK1, I am not trying to decrease my prop size...

CK1, I am not trying to decrease my prop size just keep from getting too much larger than I was using but increasing thrust and reducing rpms if all that is possible.
Forum: Gas Engines
08-31-2014, 05:50 PM
Replies: 6
Views: 456
Posted By GVR-4579

I it is a 25cc, I did fairly extensive mods to...

I it is a 25cc, I did fairly extensive mods to the motor. I was thinking about trying a 16x8 3 blade as thats what is in stock at my LHS. The model is a Pitts Ultimate Bipe. Thanks for the...
Forum: Gas Engines
08-31-2014, 06:13 AM
Replies: 6
Views: 456
Posted By GVR-4579

Prop Sizing

Hello,

I am working with a converted weedeater engine but my question only pertains to the prop. I am spinning a 15x8 up tp 12000 RPMs on the ground, much to high. I would like to switch to a 3...
08-30-2014, 04:32 AM
Replies: 5
Views: 442
Posted By GVR-4579

From research it sound like it probably is a...

From research it sound like it probably is a brown out, however I didn't realize the Beam helix were so old already and will have to source parts and fit them appropriately before i can test.
08-28-2014, 03:41 AM
Replies: 5
Views: 442
Posted By GVR-4579

Thanks for the idea, I will look into it. I have...

Thanks for the idea, I will look into it. I have to wait for repair parts before I can really test it out.
08-27-2014, 09:19 AM
Replies: 5
Views: 442
Posted By GVR-4579

I tested the battery this morning at work, with...

I tested the battery this morning at work, with no load it is still at 15v
08-26-2014, 03:02 PM
Replies: 5
Views: 442
Posted By GVR-4579

Help me diagnose my problem!

Hello,

I have been having a plauge of problems with my Beam E4. This is particularly annoying because all parts are mail order, otherwise I love this heli. The hell itself is rock solid and very...
10-19-2009, 07:30 PM
Replies: 7
Views: 1,227
Posted By GVR-4579

RE: new Raptor 30 V2 engine problem

A header tank just acts as an air trap and helps keep you from getting an air bubble into your carb line. Have you leaned the engine out from the break in settings?
10-19-2009, 07:26 PM
Replies: 7
Views: 2,562
Posted By GVR-4579

RE: OS 37 SZ-H Engine Tuning Problems

Have you cleaned the carburator?
10-18-2009, 09:57 AM
Replies: 7
Views: 815
Posted By GVR-4579

RE: Small Heli for First timer, BUT with experience...

I would also reccomend something better then the Blade CP. I have had many many headaches caused by blade CP's. However my first good heli was much more stable and actually fun to fly. Get something...
10-13-2009, 08:17 PM
Replies: 3
Views: 743
Posted By GVR-4579

RE: MCX drifts backwards

Maybe the pushrods or servo arms are not set correctly.
10-13-2009, 06:31 PM
Replies: 0
Views: 292
Posted By GVR-4579

Rator 50 v2 Trimming

Ihave a question on trimming my raptor 50v2.

When hovering or climbing it is dead on perfectly trimmed. If you are loosing altitude it will bank just a tiny bit to the right, easily correctible...
08-15-2009, 12:23 PM
Replies: 18
Views: 1,927
Posted By GVR-4579

RE: Pull pull help needed

Mike you want the cables to stay tensioned all the way both directions. Make sure the all the distances from the center lines of the pivots points are the same. Your 4" offset on the control arm also...
Forum: Beginners
08-15-2009, 12:09 PM
Replies: 18
Views: 1,394
Posted By GVR-4579

Forum: Beginners
08-13-2009, 09:47 PM
Replies: 108
Views: 6,528
Posted By GVR-4579

RE: Minnesota Fun Fly?

Definatly let me know if another one happens, i never get to fly enough and am always looking for flying buddys.
Forum: RC Jets
08-10-2009, 09:38 PM
Replies: 52
Views: 5,998
Posted By GVR-4579

RE: Minnesota Jet Rally 2009

Hopefully will be there to spectate sounds great! I love turbine noise. I dont think my edf will be up for it tho, too many issues with it.
Forum: RC Jets
08-08-2009, 10:03 PM
Replies: 6
Views: 914
Posted By GVR-4579

RE: New jet member

Congrats! I love jets but it will be quite a while before i get one.
08-08-2009, 07:37 PM
Replies: 144
Views: 16,836
Posted By GVR-4579

RE: Northern Alliance Military Fly-in - Owatonna, MN 8/8 thru 8/10

Just got home from the fly in today, great turn out!
Forum: 3D Flying!
08-07-2009, 07:54 PM
Replies: 23
Views: 1,418
Posted By GVR-4579

RE: Spoilerons any fun??

Hmm so many different funny names for ways surfaces move inrelationship to eachother. I thought flaperons were just the ability to drop the ailerons into flaps. LOL someday i will learn it all...
Forum: ARF or RTF
08-07-2009, 07:52 PM
Forum: 3D Flying!
08-07-2009, 06:40 PM
Replies: 23
Views: 1,418
Posted By GVR-4579

RE: Spoilerons any fun??

Hmm mine are set different than you guys. my elevator goes up and my spoilerons go down, makes it loop really really fast.
08-06-2009, 10:47 PM
Replies: 5
Views: 1,012
Posted By GVR-4579

Raptor .30 Parts availability

Hello,
My LHS has a raptor .30 for a good price, i was considering buying it, but I was wondering if i should wait and buy a V2 instead. Are parts readily available for the V1? Are there any...
Forum: Gas Engines
08-06-2009, 10:40 PM
Replies: 22
Views: 1,566
Posted By GVR-4579

RE: Good cutoff for 1st gasser

I have the smartfly one and it has worked great, it also has a led to inidcate if its on or not.
Forum: Beginners
08-06-2009, 09:02 PM
Replies: 24
Views: 1,918
Posted By GVR-4579

RE: trainee etiquette

As a person who has taught a few people, all i am looking for in return os someone to fly with! MOre people to fly with is always good
Showing results 1 to 25 of 59
 


 
Forum Jump

Contact Us Archive Advertising Cookie Policy