Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: Bax

Page 1 of 40 1 2 3 4

Search: Search took 1.24 seconds.

  1. Replies
    2
    Views
    56

    The RC version can use 8 x 6, 9 x 4, or 9 x 5...

    The RC version can use 8 x 6, 9 x 4, or 9 x 5 propellers.

    Yes! Use an all-castor fuel. At least 20% oil content by volume.
  2. Thread: 12FG Data Reset

    by Bax
    Replies
    2
    Views
    38

    You will always have one model in the...

    You will always have one model in the transmitter, you cannot delete the last one, so you make a new, unprogrammed one, select it as the current model, and delete the old one.

    Or just go into...
  3. Replies
    8
    Views
    80

    It sounds like the needle seat has been damaged...

    It sounds like the needle seat has been damaged at some time. That's why the needle turns so far in when trying to lean the engine. You need a new carburetor body to fix that. The needle seat is...
  4. Thread: Crystals?

    by Bax
    Replies
    1
    Views
    61

    They are. You just need to know which receiver...

    They are. You just need to know which receiver you have so that the proper crystal can be purchased.
  5. Replies
    8
    Views
    80

    The pump should not be disassembled. If you take...

    The pump should not be disassembled. If you take the regulator apart, make sure you keep the small internal parts together and in the correct order. The diaphragm may be glued to one of the...
  6. Replies
    8
    Views
    80

    You need to check for trash in the fuel system. ...

    You need to check for trash in the fuel system. It's a leading cause of sensitive needles. When you get trash in the system, the engine doesn't get enough fuel, so fuel pressure becomes lower than...
  7. Replies
    1
    Views
    34

    O.S. doesn't talk about what may or may not be in...

    O.S. doesn't talk about what may or may not be in development so we cannot make any kind of guess on this topic.
  8. Thread: Servo arms

    by Bax
    Replies
    1
    Views
    52

    Here's the link to the servo arm page: ...

    Here's the link to the servo arm page:

    http://www.futaba-rc.com/parts/futm1980.html

    If it says it's for the 28/48 servos, it will work with your servos.
  9. Thread: R7008sb

    by Bax
    Replies
    1
    Views
    66

    The S-Bus2 port is for telemetry input as well as...

    The S-Bus2 port is for telemetry input as well as control output. You can use either port for controlling servos.
  10. Replies
    1
    Views
    60

    Here are the stock numbers and list prices of the...

    Here are the stock numbers and list prices of the parts you asked about:

    FUTM4405 MM-TC-FG 12FG TRAINER CORD US$44.99

    These parts can be ordered through any hobby retailer who sells...
  11. Replies
    2
    Views
    83

    The 10CAG comes with a more expensive receiver.

    The 10CAG comes with a more expensive receiver.
  12. Replies
    2
    Views
    52

    The normal sequence is: 1) Remove cylinder ...

    The normal sequence is: 1) Remove cylinder head; 2) Remove rear cover; 3) Slide cylinder liner up, out of the case; 4) Move piston and rod assembly aft to take the rod off of the crank pin. The...
  13. Standard shipping is $9.99 on all non-warranty...

    Standard shipping is $9.99 on all non-warranty work.
  14. A gyro-only maintenance check is $18.50, but...

    A gyro-only maintenance check is $18.50, but does not include any repairs.
  15. Replies
    1
    Views
    72

    Some of those specs were written and published...

    Some of those specs were written and published before the transmitter was actually released.

    You can have up to 10 characters for both the model name and the user name.

    You can adjust how...
  16. First off, you're not powering the gyro...

    First off, you're not powering the gyro correctly. It is rated for 6.0V Maximum, but will be better off at a lower voltage. It's recommended to regulate it at 5.2V. This could be causing the gyro...
  17. Replies
    1
    Views
    66

    That's how Futaba bills it.

    That's how Futaba bills it.
  18. Replies
    2
    Views
    64

    Other than the case, supercharger, crankshaft,...

    Other than the case, supercharger, crankshaft, rear bearing, crankcase gasket set and intake manifold, the parts are all the same as for the FS-120 Surpass II and FS-120 Surpass-E
  19. Thread: Bearing shields

    by Bax
    Replies
    3
    Views
    52

    Omega fuel is good.

    Omega fuel is good.
  20. Thread: Bearing shields

    by Bax
    Replies
    3
    Views
    52

    You can remove them, if you wish. The "safest"...

    You can remove them, if you wish. The "safest" way to remove the shields would be to carefully pry it out. You need something with a point, like an icepick, and then work it under the groove that...
  21. First off, what are you calling "failsafe"? In...

    First off, what are you calling "failsafe"? In most cases, a failsafe event happens when a signal is lost between the transmitter and receiver. The receiver then sends the different control...
  22. We cannot help you program the Phantom 2 system....

    We cannot help you program the Phantom 2 system. We don't work with that manufacturer's equipment. With Futaba equipment, failsafe is set in the transmitter, and you just do it like it's said on...
  23. Thread: Futaba 9CA

    by Bax
    Replies
    6
    Views
    827

    Please check which channel(s) the flaps are...

    Please check which channel(s) the flaps are connected to. If you're using two channels and a mixer, check the direction of the mixer. Check the servos. Usually, flap servos have the pushrods...
  24. Replies
    3
    Views
    142

    First off, we can see that your receiver antennas...

    First off, we can see that your receiver antennas are not mounted correctly. Both are pointing to the side, essentially parallel. They should be at 90-degrees to each other: one forward and one to...
  25. Replies
    7
    Views
    180

    The SuperTigre G-2300 is built in the G20 design...

    The SuperTigre G-2300 is built in the G20 design series of engines. There never was a 2000-size engine in the G-series of engines.

    Years ago, there were engines such as the G20/.15 and the...
Results 1 to 25 of 1000
Page 1 of 40 1 2 3 4
All times are GMT -6. The time now is 03:10 AM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.