Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: W.P. Hurst

Search: Search took 0.94 seconds.

  1. Replies
    5
    Views
    167

    Would the O-rings for the 91 work? Really need...

    Would the O-rings for the 91 work? Really need one for the pipe from the carb.
  2. Replies
    5
    Views
    167

    Is a o-ring and gasket set still available for it?

    Is a o-ring and gasket set still available for it?
  3. Replies
    5
    Views
    167

    OS FS-90 rear rocker

    Does this engine have a crankcase vent?
  4. Replies
    0
    Views
    112

    Pressure Fitting O.S. 744 Muffler

    Bax, what is the correct size for a pressure fitting for a 744 muffler?
  5. Replies
    1
    Views
    199

    Throttle Lever Assembly 1.08

    Bax, can I get this 26881406 from O.S.? Towers has discontinued it and would like to have a few for stock.
  6. Replies
    3
    Views
    516

    RE: O.S. 1.08 prop

    Went with a 14x7 3 blade. Turns about 10,600rpms.
  7. Thread: 1.08 FSR

    by W.P. Hurst
    Replies
    1
    Views
    356

    1.08 FSR

    Bax, what does the FSR stand for?
  8. Replies
    3
    Views
    516

    RE: O.S. 1.08 prop

    OK, I'll try the 13x8 3blade.
  9. Replies
    3
    Views
    516

    O.S. 1.08 prop

    Bax, I use a 15x8 prop with the 1.08. Would a 14x9 three blade work as well? Need a bit of clearance. Pulling about 10lbs.
  10. Replies
    0
    Views
    106

    Four stroke glow plug

    Would a four stroke plug be to hot for a two stroke 1.08?
  11. Thread: OS 1.08

    by W.P. Hurst
    Replies
    3
    Views
    474

    RE: OS 1.08

    Would a four stroke glow plug in a 1.08 be to hot, or cause any damage??
  12. Thread: OS 1.08

    by W.P. Hurst
    Replies
    3
    Views
    474

    OS 1.08

    Bax, do you have everything to re-build a 1.08? Would like new bearings, ring, and all o-rings installed. Tune the carb as well.
  13. Replies
    1
    Views
    342

    O.S. 61 SF

    Bax, I need the stock numbers for the piston, ring and the retaining clips for the wrist pin. Can I still get those?
  14. Thread: O.S.61SF

    by W.P. Hurst
    Replies
    5
    Views
    631

    RE: O.S.61SF

    Towerhobbies has them. O.S. O-Ring I Valve #6-8H/#7L/#7M LXCS00 O.S. O-Ring IV/PRC #6H Rubber LXCS01
  15. Thread: O.S.61SF

    by W.P. Hurst
    Replies
    5
    Views
    631

    RE: O.S.61SF

    Bax, I am using a 11x7.5 nylon{Master Airscrew} Stock O.S. muffler, not using a pump, and the fuel tank is centered behind the carb and slightly elevated.
  16. Thread: O.S.61SF

    by W.P. Hurst
    Replies
    5
    Views
    631

    O.S.61SF

    Bax
    I cannot get this engine to make a transition from idle to full throttle b/c when idling it is loading up with fuel. I have replaced all 3 o rings on the mixture control valve , cleaned the...
  17. Replies
    1
    Views
    317

    1.08 Carb

    Bax, can I still get this carb with everything in it?? OSMG2428 29081000 Carburetor #7D .91-1.08
  18. Replies
    2
    Views
    839

    RE: OS 120 Surpass FS Series

    It has good compression, and I did put another glow plug in. The glow plug was not a four stroke plug and when I removed the hot shot the motor quit. The valve clearances are about .05 mm. Is this...
  19. Replies
    2
    Views
    839

    OS 120 Surpass FS Series

    Should this engine have to be rich at idle, seems very rich, and a little lean at full throttle?? The only way I can get a good idle is rich, alot of smoke. That also gives good transition to full...
  20. Replies
    2
    Views
    454

    O.S. 1.60FX Pusher

    Bax, I am going to try the 1.60 in a pusher config. I will keep the tank close to the engine with the clunk facing back, and use large fuel line. I also have the stock muffler, will it give enough...
  21. Replies
    2
    Views
    442

    RE: OS 1.60 FX

    I am using the1.60fx in a pusher config, model weight will be about 14-15lbs. Anyone tried this?
  22. Replies
    47
    Views
    15,347

    RE: Turnigy Accucel-6 50W 5A Balancer/Charger

    The charger will only go to -20. I still get a .03 difference in readings. Could be my meter is off a little.
  23. Replies
    47
    Views
    15,347

    RE: Turnigy Accucel-6 50W 5A Balancer/Charger

    Got it, thanks. I cannot get the numbers to match, about a half a volt diff between actual battery [volt meter] and the charger. Close enough, dont fly if to low on volts / Mah anyway. I take the...
  24. Replies
    47
    Views
    15,347

    RE: Turnigy Accucel-6 50W 5A Balancer/Charger

    Do you know how to calibrate the voltage? I can not remember. First check the battery with a meter,then you set the charger by pressing a combo of buttons?
Results 1 to 24 of 24
All times are GMT -6. The time now is 12:18 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.