Search: Posts Made By: Chopper9
Showing results 1 to 12 of 12
Search took 0.58 seconds.
05-08-2011, 12:21 PM
Replies: 0
Views: 537
Posted By Chopper9

Chipmunk canopy

Does anyone know where I might find a canopy for a 3W Chipmunk. Wingspan approx. 103". Grateful for any help.
Forum: RC Jets
05-21-2008, 06:51 PM
Replies: 5,002
Views: 976,356
Posted By Chopper9

RE: Bob Cat Copy Falcon 120 Jet

Anyone know if the suggested CG point of 13" aft of the leading edge next to the fuselage is a good CG point on the Falcon 120 or not. There were some real issues with the 40 size and it's CG points....
Forum: Kit Building
10-27-2006, 02:49 PM
Replies: 2
Views: 772
Posted By Chopper9

Laser Kit Cutters

I'm looking for a reliable laser kit cutter to get a Roamin Research Mig 3 cut. Anyone have any suggestions. Thanks for your time and efforts. Chopper
Forum: Kit Building
10-27-2006, 02:47 PM
Replies: 244
Views: 13,014
Posted By Chopper9

RE: AFR'S WHY NOT KITS

Does anyone recommend a reliable laser kit cutter for giant scale planes. I have the planes for a Mig 3 I would like to have cut. Thanks, Chopper
Forum: Glow Engines
06-17-2006, 04:08 PM
Replies: 1
Views: 549
Posted By Chopper9

Saito 220 Fuel Pump

Does anyone know weather or not a Perry Pump will work off the crankcase vent on the Saito 220 or not. Or are you restricted to using Saito's pump/carb set up they sell. I'm looking to buy this...
06-06-2006, 08:09 PM
Replies: 2
Views: 488
Posted By Chopper9

160 FX Bearing Removal

What is the easiest way to remove a main crankshaft bearing from the crankcase of a 160 FX. I've been told heating it in the oven works. If so how hot for how long. Chopper
06-06-2006, 08:06 PM
Replies: 2
Views: 536
Posted By Chopper9

160 FX Bearing Removal

Was is the easiest way to remove a main crankshaft bearing from the crank case on a 160FX. I'ver heard heat it up in ther oven. If this is true, how long and how hot. Chopper
Forum: Glow Engines
06-06-2006, 06:45 PM
Replies: 865
Views: 92,647
Posted By Chopper9

RE: OS engines users Club

Does anyone have any idea how to get the main crankshat bearing out of a 160FX. I have heard cooking the crankcase in the over for a while may work. If true how long and how hot "Chopper"
11-23-2005, 11:39 AM
Replies: 2
Views: 714
Posted By Chopper9

Nitro Proof Gasket Sealer

Looking for a reliable gasket sealer that is nitro proof and high temp resistance. :D
Forum: Glow Engines
11-23-2005, 10:46 AM
Replies: 43,632
Views: 2,438,879
Posted By Chopper9

RE: Welcome to Club SAITO !

I've got 3 Saito's. A .91, 1.00 and a 1.80. I'm looking for a high temp gasket sealer that will work on the exhaust. Everything I've tried just breaks down from nitro and the temps.
06-30-2005, 07:57 AM
Replies: 1
Views: 736
Posted By Chopper9

CA Models Zaphiro CG Point

Does anyone have any idea on what the actual CG point on the wing of a CA Models Zaphiro is. The wing core is 14 and one half inches and has a 63 inch wing span. Not sure what the actual wing loading...
Forum: Aerodynamics
06-29-2005, 04:06 PM
Replies: 5
Views: 1,001
Posted By Chopper9

CG point

I'm looking for the proper CG point on a CA Models Zaphiro pattern plane.
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service