Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: RCer

Page 1 of 7 1 2 3 4

Search: Search took 1.52 seconds.

  1. Replies
    2
    Views
    289

    Thank you for your reply. I have now ordered...

    Thank you for your reply. I have now ordered various assorted o-rings that I think might fit. Found a good UK webshop that ships to Denmark. It is called simplybearings.co.uk and they have really a...
  2. Replies
    6
    Views
    196

    Ok thanks w8ye. The reason I mention 2mm cross...

    Ok thanks w8ye. The reason I mention 2mm cross section is because the current seal is a flat oring which is 1.5mm on the flat side and 2mm on the cross section.

    /RCer
  3. Replies
    6
    Views
    196

    Thanks for the responses. Dimension wise does...

    Thanks for the responses.

    Dimension wise does it make sense to have the ID of the o-ring about 0.5 - 1.0mm smaller than the diamter of the carb throat or backplate or should I got for exact fit? ...
  4. Replies
    6
    Views
    196

    O-rings for glow engines - what material

    Hi

    I need to replace a few o-rings on a glow engine. I see there exist many types of different materials used for o-rings (Viton, Nitrile, HNBR, EPDM, PTFE, Neoprene, Silicone & Kalrez Rubber,...)...
  5. Replies
    2
    Views
    289

    Backplate o-ring for .49 glow engine

    Hi.

    I dissambled my MVVS .49 and found the o-ring on the back plate to be loose. Also I cannot put the backplate on without pinching the o-ring.

    Does anyone know the correct dimensions of the...
  6. Replies
    3
    Views
    388

    RE: Fuel question for MMVS .49 glow engine.

    Dear Pe

    Thank you very much for your expert advice.

    Do you think the 0% nitro, 15% synth will be enough oil to try out with or should I increase it to 20% synth?


    Thanks
    RCer
  7. Replies
    3
    Views
    388

    Fuel question for MMVS .49 glow engine.

    Hello All


    I have two MVVS .49 glow engines that are installed in a twin engine plane (one has a rerversed crank just for fun) so it is important that they run reliably. I do use on board glow...
  8. Replies
    2
    Views
    744

    RE: Futaba CB12Z versus T12Z

    Hello

    1) Plane version have rachet throttle while heli version has smooth throttle. Its very easy to change either into the other through adjustment holes in the back. its explained in the...
  9. Replies
    1,025
    Views
    288,768

    RE: Top Flite Cessna 182 build

    Jericho: Please let us know if the engine is completly hidden under the cowl or if you expect to make holes for the rocker covers.

    I just received a TF Cessna kit for Xmas so will soon start my...
  10. Replies
    1,025
    Views
    288,768

    RE: Top Flite Cessna 182 build

    Mustang: How does the cowl fit with the Saito 100? My guess is that you need to make holes in the cowl or can the saito 100 be completly hidden?


    Regards
    RCer
  11. Replies
    2
    Views
    599

    RE: Compact Flash Discontinued?

    I have a 1GB card in my 12Z and it works fine.

    /RCer
  12. Thread: Twin-Air 45

    by RCer
    Replies
    2
    Views
    708

    RE: Twin-Air 45

    Doesnt bind much at all. Might use a stronger servo than standard if in doubt but the force needed to push the rods back and force by hand is not much. I had a heavy duty servo lying around so I used...
  13. Replies
    3
    Views
    969

    RE: Futaba 12z vs 12fg 2.4

    I think the Futaba comparison chart is not up to date with the software update provided for both radios (and for the 14MZ for that matter)
  14. Replies
    6
    Views
    1,190

    RE: Updates for FUTABA transmitters NEW may 2008

    I found it here: http://www.rc.futaba.co.jp/hobby/09...w.cfm?wnm_no=74

    You need to enter TX serial. The pages are in Japanese and so is the update pdf instructions but the update works fine.
    ...
  15. Replies
    9
    Views
    925

    RE: 14 MZAP Mixing help!!!

    Can't you just assign Aileron, Aileron2, Aileron3 and Aileron 4 to the respective channels in the Linkage->Functions menu to the 4 Aileron servos and similar assign Elevator and Elevator 2 to the 2...
  16. 12Z - throttle hold, atv and curve settings

    Using my 12Z the carb on my heli is fully closed and and opened with an ATVs(end points) of 128 128.

    Whats the best way to set up


    End points: Limit travel travel limit
    Throttle hold...
  17. Replies
    4
    Views
    762

    RE: 14MZ programming

    Why use a slide and not a switch that when activated lowers the throttle by a small offset. Isn't this what the Idle Down function is for?


    Regards
    RCer
  18. Replies
    17
    Views
    6,075

    RE: HITEC servos & FASST receiver compatability

    So the 5945 should work with the nominal output voltage of 2.7v for Futaba FASST receivers?

    Thanks
    RCer
  19. Replies
    17
    Views
    6,075

    RE: HITEC servos & FASST receiver compatability

    Is this valid for all servo models or just a subset? I have the 5945MG in mind.

    Regards
    RCer.
  20. Replies
    0
    Views
    297

    Futaba 12z packaging dimensions

    Hello

    Can anyone tell me the dimensions of the Futaba 12Z packaging including the transmitter case as shipped by the dealer. If you can provide the shipping weight as well I will be very...
  21. Replies
    14
    Views
    932

    RE: MVVS .49 carburator question

    Hello DarZeelon.

    Thanks for the quick info. I am sorry to hear the nozzle changes as well (they really look very much the same, so thanks for the info). This means I cannot move it from the...
  22. Replies
    14
    Views
    932

    RE: MVVS .49 carburator question

    I have yet another carb question that I hope you experts can help me with.

    Sometime ago I broke the fuel nipple of the carb. I ordered a new carb. I now discover that the "new" carb is one of...
  23. Thread: 12Z

    by RCer
    Replies
    4
    Views
    527

    RE: 12Z

    Thank you for the info. I did not find that from my seach.

    Thanks
    RCer.
  24. Thread: 12Z

    by RCer
    Replies
    4
    Views
    527

    RE: 12Z

    How come the 12Z is no longer shown on the Futaba page http://2.4gigahertz.com/systems/radiosystems.html ?
    Also Robbe the Europe importer no longer shows it on their page.

    Regards
    RCer
  25. Are a cable linkage precise enough for throttle?

    Hello All

    I have a fit problem with my Twin-Air 45. As I have installed retracts there is not much room for a throttle servo in the narcels. Therefor I am trying to install a small (yet precise)...
Results 1 to 25 of 158
Page 1 of 7 1 2 3 4
All times are GMT -6. The time now is 06:01 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.