Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: cstoutr

Search: Search took 1.01 seconds.

  1. Thread: Caldera 3.0

    by cstoutr
    Replies
    9
    Views
    804

    RE: Caldera 3.0

    What plug is good for this motor. I need to get a few. This has turned into a challenge.lol I have decided to try to get it running right. I feel like with a little help from y'all I can do it.
  2. Thread: Caldera 3.0

    by cstoutr
    Replies
    9
    Views
    804

    RE: Caldera 3.0

    Yea, I'm glad nitro Heli motors arnt this difficult.lol I havnt tried one yet but I will. I'm going to tear the motor down and check the gaskets and intervals. He flipped it and broke one of the...
  3. Thread: Caldera 3.0

    by cstoutr
    Replies
    9
    Views
    804

    RE: Caldera 3.0

    Go ahead and make fun,lol. I'm not blaming the motor. I know there are easier motors to tune though. I don't think the motor is done for either. It will not start unless fuel is forced into the carb....
  4. Thread: Caldera 3.0

    by cstoutr
    Replies
    9
    Views
    804

    RE: Caldera 3.0

    I have been trying to get it to run for a friend. It will run about 5 seconds and quit. I have adjusted both needles with no change. It's possibly an air leak but I can't seem to find it. I'm done...
  5. Thread: Caldera 3.0

    by cstoutr
    Replies
    9
    Views
    804

    Caldera 3.0

    What are some good alternate motors for the caldera 3.0? I'm looking for something that will bolt right up and run reliably. The SH18 just won't cooperate with me.
  6. Replies
    29
    Views
    4,449

    RE: All of these ARFs being massed produced...

    It seems like it would be a dream job but I have talked to many guys in the hobby that make a living in the hobby and they say it was a dream and now it's a job. It was only a dream job for a short...
  7. Replies
    0
    Views
    853

    V120D02S head setup

    This video is a general guide for setting up the head on a micro CP heli with any radio.

    http://www.youtube.com/watch?v=SLinkOMKc1k&feature=youtube_gdata_player
  8. Thread: 1st Heli

    by cstoutr
    Replies
    18
    Views
    2,196

    RE: 1st Heli

    Hello and welcome. I'm not sure about the Revell brand but the biggest thing to look at as a beginner is support and parts. Have you looked at any of the Blade coaxial or fixed pitch helis. They are...
  9. Replies
    4
    Views
    565

    RE: thunder tiger e325

    Ok I was thinking about the tail pitch slider. You are talking about the arm that the servo rod goes to. You should have a bushing and washer that goes in to keep it from binding when you tighten the...
  10. Replies
    4
    Views
    565

    RE: thunder tiger e325

    Is it stiff or does it seem like it just won't move? You might try to oil it and free it up or take the tail shaft out and sand it down just a little.
  11. Replies
    6
    Views
    577

    RE: Regarding 3 Channel RC Helicopter

    Ok it's hard to tell from the pics but are both of the motors turning when power is applied?
  12. Replies
    6
    Views
    577

    RE: Regarding 3 Channel RC Helicopter

    Do you have two motors on the bottom? One spins the top rotor and the other spins the bottom. Are they both spinning when you apply power?
  13. Replies
    6
    Views
    577

    RE: Regarding 3 Channel RC Helicopter

    Ok, it looks like the maingear has disengaged from the motor. The main shaft that holds the blades has two large gears on the bottom of it. Make sure those gears are still in line with the motors. If...
  14. Replies
    6
    Views
    577

    RE: Regarding 3 Channel RC Helicopter

    I'm sure it can. You may or may not need parts but I know it can be fixed. Can you take some pics so we can see what's going on?
  15. Replies
    21
    Views
    1,478

    RE: Need suggestions for 1st Heli

    Those are great recommendations but also consider the coaxial micros for good indoor fun. The blade mcx is a perfect starter heli. It teaches the basics and is stable enough to hover hands off. He...
  16. RE: Airtronics 94814 Micro Digital Fast Servo

    Thatservo would be great on the tail of a 450 sized heli.
  17. Replies
    0
    Views
    552

    Helicopter tech

    I will repair, build, setup, or troubleshoot you helicopter. I live in Louisiana. You can pm me with questions or any needs. Price depends on amount of work and parts. All helis welcome.
  18. Replies
    1
    Views
    583

    RE: Thunder Tiger Mini Titan

    Why not go with an Align 450Pro V2? As for radio, I have an airtronics10 channel but the 8 channel will do just fine. It has a few more heli features than the 6ch. If you are interested, pm me. I can...
  19. Replies
    10
    Views
    1,745

    RE: Best place to buy Walkera

    Bob over at HeliRcStore has some great prices, parts, upgrades, and support for Walkera and other brands. www.HeliRcStore.com
  20. Replies
    2
    Views
    571

    RE: Mcpx night flying

    Cool video, did you make those yourself? How much to make me some?
  21. Replies
    34
    Views
    2,038

    RE: AMA and park fliers, another thought.

    I think that the AMA should recognize parkflyers as a SIG. I find myself trying to find a safe place to fly that is close to home. My flying site where I fly my nitro planes is about 30min. away...
Results 1 to 21 of 21
All times are GMT -6. The time now is 05:03 AM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.