Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: nonstoprc

Page 1 of 40 1 2 3 4

Search: Search took 0.99 seconds.

  1. Replies
    3
    Views
    366

    If you can quite freely rotate the shaft before...

    If you can quite freely rotate the shaft before attaching the gear box to the motor, then the problem could be somewhere else.
  2. Thread: Jeti esc

    by nonstoprc
    Replies
    7
    Views
    653

    big_G, Sorry no, I do not have one.

    big_G,

    Sorry no, I do not have one.
  3. Thread: Jeti esc

    by nonstoprc
    Replies
    7
    Views
    653

    Also make sure you can set the throttle end...

    Also make sure you can set the throttle end points (low and high, typically 1.2ms for low and 1.9ms for high) on the ESC. Without that feature, you may have different throttle low and high position...
  4. Replies
    2
    Views
    164

    Hi Max, Thanks for the information. Will send...

    Hi Max,

    Thanks for the information. Will send the radio in once the season is over. The radio was purchased in Jan. 2011 (brand new).
  5. Replies
    2
    Views
    164

    Black out display in 12Z

    Hi,

    The left half of the LCD display screen on my 12z becomes blackout after power-up. See the photo attached. Other than not being able to see anything, or making adjustment of parameters shown...
  6. Replies
    1
    Views
    415

    I have posted a new sales ad for the additional 4...

    I have posted a new sales ad for the additional 4 tubes here http://www.rcuniverse.com/market/item.cfm?itemID=1032439. Thank you for your attention.
  7. Replies
    1
    Views
    415

    Shell Stamina RL2 grease

    I have several tubes of Shell Stamina RL2 grease for sale. Please check out RCU sale item 1032269 http://www.rcuniverse.com/market/item.cfm?itemid=1032269&electric=0.
  8. Replies
    8
    Views
    1,153

    With Neu, I found the start power at -20 is...

    With Neu, I found the start power at -20 is adequate with APC props for a smooth start. For lighter falcon carbon fiber V2 props, the -20 setting still gives an impression of rough start. -50 as...
  9. Thread: Epoxy tip

    by nonstoprc
    Replies
    52
    Views
    3,147

    Yes, business cards, or digital hotel door keys...

    Yes, business cards, or digital hotel door keys etc. Squeeze out only 1/2 of needed amount from each tube. And one such card can be used for long long time (front and back side).

    For mixing, I...
  10. Replies
    132
    Views
    10,983

    Interesting. The discontinued Futaba 12Z...

    Interesting.

    The discontinued Futaba 12Z also allows 8 flight conditions.
  11. Replies
    132
    Views
    10,983

    Great info! Hopefully Futaba offers flight...

    Great info! Hopefully Futaba offers flight conditions with 18SZ in airplane mode.
  12. It may not be a bad idea to inspect the gears and...

    It may not be a bad idea to inspect the gears and add some grease if needed.
  13. thanks!

    thanks!
  14. Heat shrink tube seen on the antenna cables on a new Futaba 617fs receiver

    I received a new copy of the receiver from a US hobby shop and noticed that a section of the antenna cable is protected by some heat tube. See the picture. This happens to both cables at the same...
  15. Thread: Hacker

    by nonstoprc
    Replies
    19
    Views
    1,616

    Hope that the Hacker line of Jeti Mezon ESCs will...

    Hope that the Hacker line of Jeti Mezon ESCs will be distributed by the new US distributor.
  16. Replies
    143
    Views
    25,038

    I cut 2mm solid carbon fiber rod into proper...

    I cut 2mm solid carbon fiber rod into proper length as the push rod for all control surfaces. The two ends are 2.5mm ball bearing adjusters...
  17. Replies
    8
    Views
    678

    My throttle setup uses a curve that allows more...

    My throttle setup uses a curve that allows more power in the low and middle range. Motor is Neu F3a and ESC is Mezon 95 opt.

    2049517
  18. Or get a chuck extension such as this one...

    Or get a chuck extension such as this one http://www.harborfreight.com/12-in-uick-change-hex-bit-extension-68516.html.
  19. Replies
    8
    Views
    1,078

    I have Champion 73538i 2000w inverter charger. ...

    I have Champion 73538i 2000w inverter charger. In eco-mode, it is super quite (@52db) and can power 3 cellpro 10s chargers (~3 x 280w) without any issues. Bought it from amazon.com @ $400 2 years...
  20. Replies
    5
    Views
    340

    check out the two long screws that hold the carb...

    check out the two long screws that hold the carb to the engine. If they are backed out a little bit, a leak can develop.
  21. Replies
    13
    Views
    1,773

    Scott, thanks and it will be fun to fly the...

    Scott,

    thanks and it will be fun to fly the 2015 Advanced.

    Just wonder what is the thinking behind making the Advanced one year deal. Is it a trend?

    Thanks
  22. How do you compare the PT carbon prop with a...

    How do you compare the PT carbon prop with a Falcon?
  23. Of course, for charging you can get away with...

    Of course, for charging you can get away with connectors with less capability. But I think the focus of the discussion is on connectors airborne.
  24. I think APP PP75 is the type of connector more...

    I think APP PP75 is the type of connector more relevant to 2M pattern applications.
  25. I have been using HXT 4mm bullets on EP pattern...

    I have been using HXT 4mm bullets on EP pattern applications, connecting battery packs to ESC, and ESC to motor, without any problem. Never had one instance of open or short circuit.

    Had problem...
Results 1 to 25 of 1000
Page 1 of 40 1 2 3 4
RCU Reviews
All times are GMT -6. The time now is 11:39 AM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.