Search: Posts Made By: Hilarious
Showing results 1 to 25 of 42
Search took 0.34 seconds.
Replies: 6
Views: 1,258
Posted By Hilarious

RE: JR 9303 problems

R-
I have your elevator spring for you, in the mail today Ihope,
05-15-2009, 02:32 PM
Replies: 5
Views: 1,270
Posted By Hilarious

RE: Dual elevator setup spectrum radio

Be sure to run Aux 2 travel adjust to 0 both directions, this will inhibit the switch. Adjust the aux two travel by changing % of mix, this will make both left and right elevators move the same...
05-12-2009, 01:24 PM
Replies: 5
Views: 720
Posted By Hilarious

RE: Uneven travel in elevators

I think the problem here may have to do with which mix you are using. With the DX7 only mixes 5 and 6 have matching trim. It is perfectly normal for the travel to not be exactly the same on each...
05-12-2009, 01:07 PM
Replies: 10
Views: 845
Posted By Hilarious

RE: Dual 2.4s

Why not do the bind operations your self and see if there is any difference? Don't make any changes in the TX programming.
05-12-2009, 01:04 PM
Replies: 3
Views: 785
Posted By Hilarious

RE: AR9300 rx , no satelites available yet

doc,
It includes one remote with the 203mm antenna. I don't understand your issue??
Replies: 10
Views: 1,060
Posted By Hilarious

RE: AR9000 Firmware or Hardware Bug?

Put a JR servo on the rudder and report back.
Replies: 10
Views: 1,226
Posted By Hilarious

RE: UNBELIEVABLE for JR module/rcvr combo

SAM Some one led you astray, 7ch is 109.99 9ch is $179.99 Click this link. I just don't understand why people wont look on the Horizon Web site???

...
03-11-2009, 01:25 PM
Replies: 22
Views: 4,420
Posted By Hilarious

RE: BUG in the DX6i software ?

Just looked at the DX6i D/R Expo menu screen. Are you clicking ib Expo INH then changing that value from "0" to the value you want, say 30% or are you just changing the 100% value that is showing on...
03-11-2009, 01:13 PM
Replies: 27
Views: 6,392
Posted By Hilarious

RE: DX6i and AR 6000's

Tell me, I am confused, why would you even think of flying the model if the radio is not responding to the transmitter?? I am pretty confident if you repeat this a number of times it will alwasy do...
03-05-2009, 05:07 PM
Replies: 4
Views: 579
Posted By Hilarious

RE: ONEWASP-A STREIGHT SHOOTER

Yep, just order up the gear set for the 3421 JRPSG3421 I only use one metal gear to keep the weight down. To bad you can't buy just the next to last gear in the train. This method also takes up...
03-04-2009, 03:03 PM
Replies: 4
Views: 579
Posted By Hilarious

RE: ONEWASP-A STREIGHT SHOOTER

Frankly, I find the MN48 has way more torque than required for the application where you would use it. I have broken gears by bumping the control surface (rudder, you know, it gets bumped). There...
01-12-2009, 01:55 PM
Replies: 3
Views: 541
Posted By Hilarious

RE: 9303 2.4 - throttle cut

Do the "programed failsafe postition"

Turn Rx on in bind mode, remove bind plug.

Turn TX on in Bind mode with ALL controls in failsafe position (including correct retract switch position)
...
Replies: 12
Views: 1,075
Posted By Hilarious

RE: 9303 2.4 problems, ?

Just as a reminder because people always seem to forget to mention. The wire chafing issue ONLY applies to X9303 not XP9303. In the 2.4GHz version there is a voltage regulator (?) mounted in the...
Forum: Q-40 Racing
01-05-2009, 11:34 PM
Replies: 7
Views: 2,228
Posted By Hilarious

RE: new sweet V

Hi All,
The Sweet Vee will be available in the very near future, final testing has been completed and production models are in process at this time. The models that Gary and Tom built were final...
Replies: 34
Views: 2,880
Posted By Hilarious

RE: DX7 Fail safe

Zeeb,
Would you please grab a DX7 with AR7000 having Quick Connect (flashing lights) feature and do the programed failsafe just as if it was a X9303. Hold the TX sticks until the RX light comes on...
Replies: 34
Views: 2,880
Posted By Hilarious

RE: DX7 Fail safe

The basic TWO Bind modes do confuse everyone.
When you do the regular bind with the sticks neutral, gear down etc the reciever will send all controls to those positions ONLY on startup. This is...
Replies: 34
Views: 2,880
Posted By Hilarious

RE: DX7 Fail safe

Zeeb,
There is more than one Fail safe in the Spektrum radios.

Take your DX7 using the updated AR7000 with Quick Connect feature. Put the RX in Bind mode, remove the bind plug leaving the...
Replies: 4
Views: 620
Posted By Hilarious

RE: JR data transfer

Hello,
Let me point to the reason there is no differnetial in "Wing Type Normal" When you have this case you are using one aileron servo or a Y cord. In which case you can not do differnetial at...
Replies: 26
Views: 2,500
Posted By Hilarious

RE: JR 12X Data Trans Program compatability

Howard,
Actually the program was written before Vista came on the scene. It does work in 32 bit but I have not tried it in a 64 bit machine.

That said the FIRST thing to test is the position...
Replies: 6
Views: 1,770
Posted By Hilarious

RE: Making spoilers/flaps out of ful span ailerons on Spektrum Dx7??

Bush,
But on the average you are just fine. Hmm, seems like I heard that someplace?? Hope all is well.
Replies: 6
Views: 1,770
Posted By Hilarious

RE: Making spoilers/flaps out of ful span ailerons on Spektrum Dx7??

Actually it is a really basic setup in the DX7,

Put right wing servo into aileron slot, left wing servo into AUX1

Set the Wing type to Flaperon, and set the servo reverse swithches to get...
Replies: 18
Views: 3,786
Posted By Hilarious

RE: Spektrum DX6i

Gassit,
Check a couple things. Check the servo travel settings for throttle. Should be 100%, On AR6200 (like 6100) the first slot is for battery not ESC, second slot is for throttle or ESC, then...
Replies: 10
Views: 1,174
Posted By Hilarious

RE: Binding without a place to plug binder

Yes, the bind process is different. It is easier, no bind plug required, just check the instruction with the Vapor. The Cessna, Citabria, Ember are not DSM2 and there fore not compatible with your...
Replies: 4
Views: 731
Posted By Hilarious

RE: 12x 10x questions

The 12X has it's own version of the USB Data Transfer program. It is not compatible with the JR USB Data Transfer program that is sold for the 9303 and 10X radio versions.

It is compatible with...
Replies: 8
Views: 793
Posted By Hilarious

RE: Help with X9303, aileron set-up.

Erik,
Really it is very easy. Check the video link in this article. It talks about the JR Data Transfer program but the video outlines the dual aileron and dual elevator setup and even includes...
Showing results 1 to 25 of 42
 


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service