Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: rc4flying

Page 1 of 24 1 2 3 4

Search: Search took 0.95 seconds.

  1. Replies
    229
    Views
    13,543

    I am finishing up a Pro for a guy with a P300 and...

    I am finishing up a Pro for a guy with a P300 and thrust vectoring.
  2. Replies
    229
    Views
    13,543

    Well guys, "Good Luck" with all your maiden...

    Well guys, "Good Luck" with all your maiden flights and I know you will have a lot of fun with plane.
  3. Replies
    229
    Views
    13,543

    Thanks Bob. These Pro's are just so solid at any...

    Thanks Bob. These Pro's are just so solid at any speed.
  4. Replies
    229
    Views
    13,543

    Just be careful, those low slow passes are...

    Just be careful, those low slow passes are addicting.
  5. Replies
    229
    Views
    13,543

    You guys are going to love this plane. I can't...

    You guys are going to love this plane. I can't fly mine enough. A really straight and true flyer.
  6. Replies
    12
    Views
    877

    The build is basically done, but we are still...

    The build is basically done, but we are still waiting on a new motor to be shipped.
  7. Replies
    229
    Views
    13,543

    I started with all the throws listed and they...

    I started with all the throws listed and they were a very good safe start for a maiden flight. I presently have the rudder set at 2-1/8" throw in both directions measure at location shown on above...
  8. Replies
    229
    Views
    13,543

    The arrows are pointing to where your...

    The arrows are pointing to where your measurements should be taken at for control surface throw measurements.

    I have my C/G at the back edge of wing tube and I am totally happy with the plane.
  9. Replies
    3
    Views
    230

    http://forum.powerbox-systems.com/ At this...

    http://forum.powerbox-systems.com/

    At this link, you may want to register than ask about getting a download for the manual under the Champion RRS forum
  10. Replies
    37
    Views
    3,014

    I have one of the early sets of these electric...

    I have one of the early sets of these electric gear with just above 100 flights. I have only had one brass piece start to strip out, but was caught early after about 25 flights. Changed this piece...
  11. Replies
    229
    Views
    13,543

    FenderBean, Sorry about posting the above in...

    FenderBean,
    Sorry about posting the above in your build thread. There was a Rebel thread about the use of thrust vector usage in a Rebel Pro and when I did a search for that thread, I now see that...
  12. Replies
    229
    Views
    13,543

    The owner has picked Futaba 9157.

    The owner has picked Futaba 9157.
  13. Replies
    229
    Views
    13,543

    I now have the tail section with a Thrust...

    I now have the tail section with a Thrust Vectoring pipe all set up and ready to go. This is a build that I am doing for a friend.
  14. Replies
    229
    Views
    13,543

    I now see why I thought your gear setup looked...

    I now see why I thought your gear setup looked strange, you have it further back on the mounting rails than I positioned mine. Sorry for the misunderstanding.
    I like the gear leg covers. Might have...
  15. Replies
    229
    Views
    13,543

    I will have to do this on my new one which...

    I will have to do this on my new one which arrives later this week.
  16. Replies
    229
    Views
    13,543

    Wow, I would have thought that it would have...

    Wow, I would have thought that it would have taken more sanding in that area of the flex plate, so that is why I just cut it. Great job.
    I use #6 screws for mounting the gear with the holes to...
  17. Replies
    229
    Views
    13,543

    Yea, I had brain stormed on it as well, and will...

    Yea, I had brain stormed on it as well, and will be interested on what you may come up with.
    I have 65 flights on mine and I have not seen how cutting the plate like it did had hurt in any way.
  18. Replies
    229
    Views
    13,543

    Yes, that flex plate does hit the air cylinder...

    Yes, that flex plate does hit the air cylinder with the Air Tech gear. I cut the flex plate to make them 2 rail reinforcements. as you may be able to see in the first pic without the gear installed.
  19. Replies
    229
    Views
    13,543

    I just finished my wings on my project, and I...

    I just finished my wings on my project, and I know that you plan on cutting for gear leg covers, but the strut lengths on the Air Tech gear are straighter and longer. It could be how you plan on...
  20. Replies
    229
    Views
    13,543

    Which Landing gear are you using ? If you are...

    Which Landing gear are you using ? If you are using the Air-Tech Germany gear, than I am pretty sure you are using the wrong pattern for the main retracts.
  21. Replies
    229
    Views
    13,543

    FenderBean, Looks like the one I am working on...

    FenderBean, Looks like the one I am working on for a friend.
    Enjoy your build.
  22. Replies
    12
    Views
    877

    The pipe it self measures 31 1/2". the bell mouth...

    The pipe it self measures 31 1/2". the bell mouth adds 2 1/2" and the thrust vector nozzle extends another 1 1/2" beyond the pipe's length. So overall the the pipe assembly ready to install is 35...
  23. Replies
    229
    Views
    13,543

    As of right now, there are no plans to change...

    As of right now, there are no plans to change anything. The motor is supposed to ship today, so later next week, I will see how it fits.
    As for the inlets, I think that would not be possible because...
  24. Replies
    229
    Views
    13,543

    I am in the process of building a Pro with this...

    I am in the process of building a Pro with this very combo now. Hope to have it in the air before the end of the year.
  25. Replies
    229
    Views
    13,543

    Looks good.

    Looks good.
Results 1 to 25 of 589
Page 1 of 24 1 2 3 4
RCU Reviews
All times are GMT -6. The time now is 04:50 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.