Search: Posts Made By: srttruck
Showing results 1 to 14 of 14
Search took 0.36 seconds.
09-27-2009, 08:49 AM
Replies: 18
Views: 1,739
Posted By srttruck

RE: avenger W / QD25

Peerpsi, yes it is the pro hull.

Anbjorn, i have the strut at 7/16 above the bottom right now. I will see how that works out then adjust from there,

Does everyone who runs the speedmaster...
09-26-2009, 07:20 PM
Replies: 18
Views: 1,739
Posted By srttruck

RE: avenger W / QD25

In reguards to the speed master vs aeromarine hardware, no its not the same bolt hole allignment. I filled the holes then re setup the new speedmaster hardware.

I cut out the rear out of the...
09-26-2009, 10:44 AM
Replies: 18
Views: 1,739
Posted By srttruck

RE: avenger W / QD25

I was thinking of drilling a series of 5/8" holes (approx 10 ) across the top of the transom, rite under where the hatch meets the hull. I was also thinking about adding 2 more air entry scoops on...
09-26-2009, 09:07 AM
Replies: 18
Views: 1,739
Posted By srttruck

RE: avenger W / QD25

UPDATE: I have the boat about 90% complete, for the prop i went with a 6717/3 - 415C from Chris Hoffman. I ditched all the AM hardware and went with Speedmaster. Also decided to not use a clutch. I...
09-14-2009, 04:20 AM
Replies: 18
Views: 1,739
Posted By srttruck

RE: avenger W / QD25

ok, thats good to hear. do you know your running weight and cg?
09-14-2009, 04:18 AM
Replies: 18
Views: 1,739
Posted By srttruck

RE: avenger W / QD25

Thanks! its work in progress, I hope to have her in the water by end of sept. btw I made the graphics, They are vinyl decals.
09-13-2009, 03:28 PM
Replies: 18
Views: 1,739
Posted By srttruck

avenger W / QD25

Long time lurker here... I have finally retired my old prather fun cruiser that had a modded 26. She spent more time upside down than she did uprite..[:@] Anyhow, I just purchased a AM avenger and...
12-21-2008, 09:09 PM
Replies: 9
Views: 3,738
Posted By srttruck

RE: Zenoah G26 rebuild questions?

i tore the engine down tonight. The cylinder and piston are free from scratches,. I am wondering about the ring gap on the piston and the ring. Does anyone know how wide the ring is supossed to be?...
12-20-2008, 10:31 PM
Replies: 9
Views: 3,738
Posted By srttruck

RE: Zenoah G26 rebuild questions?

I'm going to take it apart tomorrow and let you know exactly whats going on. I changed oils (went with redline @ 26:1)) and it ran to lean. light grey plug with little bb's attached to it
12-20-2008, 08:53 PM
Replies: 9
Views: 3,738
Posted By srttruck

Zenoah G26 rebuild questions?

Ok,, I have a zenoah g26 that has lost compression. What is going to be the best top end kit that will give me of course more power and be reliable. My motor currently is stock except outerwears and...
09-28-2008, 08:55 AM
Replies: 10
Views: 1,072
Posted By srttruck

RE: fg monster wont start...

This happened to my leopard not to long ago. bought a new plug, cleaned the carb and even tried starter spray with no sucess. What it ended up being was somehow fuel got into the crankcase. I pulled...
02-01-2008, 11:41 AM
Replies: 1,311
Views: 316,255
Posted By srttruck

RE: Building the Hangar 9 Cessna 182 Skylane

Hey guys, I have been following this thread for a while now but unfortunitly i have to abandon my h-9 cessna project, it is brand new in the packing nothing assembled. pm me if your looking for one....
09-09-2007, 08:50 AM
Replies: 14
Views: 748
Posted By srttruck

RE: 4wd with sand paddles

yes, i would only recommend 2 for the rear. You will not be happy with them allthoughway around. I also thought having them allthoughway around would be better so i bought 4 of them and tried it out....
09-09-2007, 08:40 AM
Replies: 14
Views: 748
Posted By srttruck

RE: 4wd with sand paddles

when you have paddles on the front of a buggy it does not turn correctly, it has a very hard time turning. It sounds odd putting a set of razorbacks on the front of a 4wd buggy, but it will perform...
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service