Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: bhady

Page 1 of 9 1 2 3 4

Search: Search took 1.14 seconds.

  1. Replies
    9
    Views
    350

    I've been using standard ni-cad and 2000 MA NMH...

    I've been using standard ni-cad and 2000 MA NMH for years without any issues, cost is low, and they last several years. I keep all mine on a timer for an hour charge every night, always ready to go.
  2. Replies
    50
    Views
    1,293

    I use air tool oil in my 2 strokes, and outboard...

    I use air tool oil in my 2 strokes, and outboard fogging oil in 4 strokes. Just use the snorkel tube in the crankcase vent tube , the oil gets up inside the engine and works its way out through the...
  3. Just remember to check the pack/connector...

    Just remember to check the pack/connector polarity, JR is reversed from Futaba and the others
  4. Replies
    106
    Views
    4,860

    Kaos, Escapade, these are both great flyers....

    Kaos, Escapade, these are both great flyers.
    bhady
  5. Replies
    1,743
    Views
    226,387

    I've powered mine with Super tiger 40 and 45...

    I've powered mine with Super tiger 40 and 45 engines, and an OS 70 surpass. The Super Tiger 45 was my favorite, and fastest, clocked on radar 105.
    bhady
  6. Replies
    23
    Views
    575

    Yes they are definitely worth buying. My...

    Yes they are definitely worth buying. My son-in-law and I both taught ourselves to fly on GP RealFlight G2 simulators about fifteen years ago. We had no choice, there was no one in the area to...
  7. Replies
    6
    Views
    521

    Standard servos work just fine. It's a fast...

    Standard servos work just fine. It's a fast little plane, I've had 40 and 46 2 strokes in it as well as an OS .70 four stroke. I've had one for 3-4 years now, you'll enjoy it.
    bhady
  8. Just rotate the carb 180 degrees. bhady

    Just rotate the carb 180 degrees.
    bhady
  9. Replies
    4
    Views
    476

    I use the "Vanessa rig" fastest and easiest...

    I use the "Vanessa rig" fastest and easiest method to get the CG set properly. Check here on RCU there are threads covering its build and use.
    bhady
  10. Replies
    100
    Views
    2,608

    I personally knew two men who were B-17 crewmen. ...

    I personally knew two men who were B-17 crewmen. Both had great respect for German aircraft and the men who flew them. Neither had an issue with any enemy aircraft markings. As noted above very...
  11. Replies
    100
    Views
    2,608

    I am sick and tired of everyone having to bow...

    I am sick and tired of everyone having to bow down to the politically correct whiners. If an enemy aircraft had a swastika on it and the model is built to represent an enemy aircraft aircraft, put...
  12. Replies
    5
    Views
    334

    I also recently picked one of these on the...

    I also recently picked one of these on the auction site. It came with a photo-copy od the instructions. It's only four pages, I'll try to scan and e-mail it to you, if that doesn't work, I'll get...
  13. I charge my RX and TX packs up and bring them...

    I charge my RX and TX packs up and bring them inside for the winter. My planes and engines (treated with air tool oil) are stored in the garage. No problems.
  14. Thread: Nylon clevice

    by bhady
    Replies
    35
    Views
    963

    Use the fuel tubing! I lost a plane a few years...

    Use the fuel tubing! I lost a plane a few years ago (Kaos ARF). I forgot to slide the tubing back over the clevis after trimming. One elevator clevis opened, with only one elevator half working,...
  15. Thread: Engine surging

    by bhady
    Replies
    16
    Views
    321

    It sounds like it's lean. Possible air leak at...

    It sounds like it's lean. Possible air leak at the carb base, back plate, or very likely at the needle valve. Try a short piece of fuel line where the needle valve screws into the spray bar to...
  16. Replies
    16
    Views
    867

    I'm 63 and used to by gas for 25.9, later for...

    I'm 63 and used to by gas for 25.9, later for 29.9 for reg., and 31.9 for premium. you could fill up for $5.00 or just booze cruise on Sat. night for a buck and $5.00 for a case of beer with a...
  17. Replies
    83
    Views
    5,433

    Thanks for the tip. bhady

    Thanks for the tip.
    bhady
  18. Replies
    83
    Views
    5,433

    This rally sucks, I was seriously considering...

    This rally sucks, I was seriously considering ordering a Chipmunk for my next project.
    bhady
  19. Replies
    42
    Views
    9,787

    I've found that my .46 engines (Tower and Super...

    I've found that my .46 engines (Tower and Super Tiger) seem to like 11X6 props best, either Master Airscrew or APC
    bhady
  20. Replies
    7
    Views
    355

    A friend and I were going to demonstrate RC...

    A friend and I were going to demonstrate RC flying to an acquaintance and his son. The guy had an open pasture about a mile from a 100 KW Am/FM transmitter tower site. My friend's plane was out of...
  21. Replies
    203
    Views
    9,552

    I think it's time for common sense, we can't and...

    I think it's time for common sense, we can't and shouldn't be trying to constantly protect our selves from every conceivable misfortune. As John Wayne once said, "Life is tough, it's even tougher...
  22. Replies
    28
    Views
    833

    Horizon Hobbies shows the spacewalker 40 ARAF in...

    Horizon Hobbies shows the spacewalker 40 ARAF in stock now. No price increase.
    bhady
  23. Replies
    28
    Views
    833

    I Put one together earlier this summer. It's a...

    I Put one together earlier this summer. It's a good looking and good flying plane, and seems to like moderate speeds best. It's Kind of a floater when landing. The covering job is excellent, no...
  24. Thread: ST Parts?

    by bhady
    Replies
    2
    Views
    590

    I am also waiting (for over a year) for Ssuper...

    I am also waiting (for over a year) for Ssuper Tiger parts. Any Idea when they will be again available?
    BHady
  25. Replies
    14
    Views
    425

    I use vinyl from a graphics shop regularly on my...

    I use vinyl from a graphics shop regularly on my glow planes for trim or puncture band-aids with no problems with lifting. This is the stuff used for vehicle graphics. Scraps can be had very...
Results 1 to 25 of 212
Page 1 of 9 1 2 3 4
All times are GMT -6. The time now is 10:00 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.