Search: Posts Made By: speedracerntrixie
Showing results 1 to 10 of 10
Search took 0.01 seconds.
Forum: Kit Building
06-09-2019, 08:38 PM
Replies: 237
Views: 9,756
Posted By speedracerntrixie

https://cimg2.ibsrv.net/gimg/www.rcuniverse.com-vb...

https://cimg2.ibsrv.net/gimg/www.rcuniverse.com-vbulletin/2000x1493/img_2603_9dee19a8a3279bd834a14853259083525c1e4a48.jpg






Vincent, with the super high quality of your build so far I...
Forum: Kit Building
05-29-2019, 05:42 PM
Replies: 237
Views: 9,756
Posted By speedracerntrixie

Looking very nice Vincent!

Looking very nice Vincent!
Forum: Kit Building
05-07-2019, 08:05 AM
Replies: 237
Views: 9,756
Posted By speedracerntrixie

I'm thinking that with full scale that efficiency...

I'm thinking that with full scale that efficiency and cost of operation is at the top of the priority list. The fat trailing edges do produce drag. On our models there is bad drag and good drag. Full...
Forum: Kit Building
05-05-2019, 06:38 AM
Replies: 237
Views: 9,756
Posted By speedracerntrixie

Not sure if it would make a difference here or...

Not sure if it would make a difference here or not but the theory is that leaving them squared off will give a bit better control feel just off center. I have tried it on my aerobatic models and it...
Forum: Kit Building
05-04-2019, 07:54 PM
Replies: 237
Views: 9,756
Posted By speedracerntrixie

Vincent, do the plans illustrate rounding the...

Vincent, do the plans illustrate rounding the trailing edges of the control surfaces?
Forum: Kit Building
04-16-2019, 08:58 AM
Replies: 237
Views: 9,756
Posted By speedracerntrixie

Vincent, as usual your building skills are...

Vincent, as usual your building skills are excellent. I look forward to seeing the finished product. Depending on how you intend to fly the airplane I would like to offer another suggestion. With the...
Forum: Kit Building
04-07-2019, 09:47 AM
Replies: 237
Views: 9,756
Posted By speedracerntrixie

Vincent, how is your CG looking?

Vincent, how is your CG looking?
Forum: Kit Building
04-02-2019, 07:55 AM
Replies: 237
Views: 9,756
Posted By speedracerntrixie

Indeed! I haven't built an all balsa and ply kit...

Indeed! I haven't built an all balsa and ply kit in 4 years. A few weeks ago I picked up an Andrews Aeromaster Two kit, Vincent is inspiring me to get the bench set up and to start framing it. Glad...
Forum: Kit Building
03-30-2019, 03:39 PM
Replies: 237
Views: 9,756
Posted By speedracerntrixie

Vincent, you donít need me to keep you honest,...

Vincent, you donít need me to keep you honest, you do fine without me. I do have something for you to think about though. Have you considered adding some right thrust? Going with a larger engine that...
Forum: Kit Building
03-29-2019, 01:32 PM
Replies: 237
Views: 9,756
Posted By speedracerntrixie

Itís very common to use 1/2Ē dowel for horn hard...

Itís very common to use 1/2Ē dowel for horn hard points. I have done them on airplanes up to 40% ( 150cc powered). I use a sharpened brass tube to cut a hole through the bottom balsa skin and foam....
Showing results 1 to 10 of 10


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service