Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: xxturbowesxx

Page 1 of 6 1 2 3 4

Search: Search took 1.15 seconds.

  1. RE: *Official* Caldera 10E Video, Picture And Discussion Thread

    As for the knuckles.

    I have stuck with plastic and when I install a new one I put jb weld in the screw hole and on the screw.. has worked very well so far you just have to be careful since you...
  2. RE: *Official* Caldera 10E Video, Picture And Discussion Thread

    2s,3s speed runs, wheelies some jumping and a mild bash.

    BH 120a esc
    Tacon 3660 540L 4000kv motor
    No body because we all know its crap and I havent found a replacement worth buying.

    ...
  3. RE: *Official* Caldera 10E Video, Picture And Discussion Thread

    We need to see a 3s video with that big motor petrock!
  4. RE: need a motor recommendation for a redcat caldera with 120a esc

    How was it compared to stock..power wise?
  5. RE: need a motor recommendation for a redcat caldera with 120a esc

    I think I decided to get a tacon 540l 4000kv motor with a 15t pinion and set the punch on my esc to the min setting because this setup is going to have a lot more power (site says 1200 watts) I have...
  6. RE: *Official* Caldera 10E Video, Picture And Discussion Thread

    I am going to install a tacon 4000kv 540L motor with my brushless hobbies 120a.

    Because I have to use 5mm mod 8 which is slightly bigger in diameter I doubt I'll be able to stick with the 16t...
  7. RE: *Official* Caldera 10E Video, Picture And Discussion Thread

    Do traxxas 32p pinions fit on the tacon 5mm shaft?

    If not What 32p pinions fit?

    Will I lose any room and not be able to run a 16t because of the larger shaft?

    Is the tacon that much...
  8. RE: need a motor recommendation for a redcat caldera with 120a esc

    Bumpity
  9. need a motor recommendation for a redcat caldera with 120a esc

    First off the esc burned out which was totally my fault but either way I replaced it with a brushless hobbies 120a because its a steal over that 80a.

    Now I need to pair it with a new motor as...
  10. RE: *Official* Caldera 10E Video, Picture And Discussion Thread

    Ran into a few issues none really the fault of the caldera .

    First off the esc burned out which was totally my fault but either way I replaced it with a brushless hobbies 120a because its a...
  11. RE: i want to build a cheap basher..real cheap

    I rewired the fan on it the problem was one of the wires was slightly exposed and grounding out causing the esc failure.
  12. RE: i want to build a cheap basher..real cheap

    Burned out the 35a esc so I ordered the brushlesshobbies 120a and going to leave the stock motor in there for now as I'm not looking for speed just an esc that doesn't hit thermal mode on 3s after a...
  13. unmatched esc to motor(overkill esc)

    Basically the esc went out on my Caldera 10e. It was only s 35a esc but seemed to always enter thermal shutdown on 3s so while looking for a replacement I just couldn't pass up a brushlesshobbies...
  14. RE: i want to build a cheap basher..real cheap

    Thanks I don't really have to upgrade the Caldera it was jut an idea because I liked the idea of using the brushless hobbies esc and wanted an excuse to buy one..

    I may get it and find another...
  15. RE: *Official* Caldera 10E Video, Picture And Discussion Thread

    Anyone know if a 80a or 120a would be an upgrade for the caldera within the stock motor?


    Just wondering which motor would work well with it.
  16. RE: i want to build a cheap basher..real cheap

    Can the evader handle brushless power?
  17. i want to build a cheap basher..real cheap

    Basically I have a brushless redcat 10e with a 35a esc that I would like to replace the a 80 or 120a so I wanted to use the 35a to put into a cheap roller..

    I have spare servos and receivers so...
  18. RE: *Official* Caldera 10E Video, Picture And Discussion Thread

    It was a direct hit at 50mph(top speed run on 3s & 16t pinion) and it recoiled to the side after impact.

    IMO I doubt any other vehicle would have survived without similar damage.

    Only...
  19. RE: *Official* Caldera 10E Video, Picture And Discussion Thread

    well i had a bad day today.. bad and good

    Good in the sense i got to do some crazy high speed runs on 3s

    Bad in I decided to run into a tree at full speed(~50mph)

    Broken front chassis,...
  20. RE: *Official* Caldera 10E Video, Picture And Discussion Thread

    I have the 10e
  21. RE: *Official* Caldera 10E Video, Picture And Discussion Thread

    I put 7k in the front and 30k in the rear and now wish I would have gone higher in the front.. the rear seems perfect for a basher and now will actually climb some rocks.

    I think perfect would...
  22. RE: *Official* Caldera 10E Video, Picture And Discussion Thread

    [quote]ORIGINAL: PetRock




    IĀ*put 10k in the front and 7k in the back... and IĀ*wish IĀ*had gone up one more on each end (maybe 15k front 10k back)? But like you I don't feel like taking...
  23. RE: *Official* Caldera 10E Video, Picture And Discussion Thread

    Installed a 16p this morning and its more what I am looking for(35-40) with plenty of punch..

    You weren't kidding about it being tight and a blast on 3s(easily 45-50)

    15p is more...
  24. Replies
    10
    Views
    1,622

    RE: redcat gears MOD

    I can't speak for the others but the Caldera 10e uses 32p pinions not the 48p.. this thread almost cost me a spur.
  25. RE: HobbyKing ..... Garbage (Refund and Return related)

    Try to deal with hobbypartz for cheap stuff if possible(like batts).

    Its no secret customer service is non existent but your experience makes me want to never buy an other thing from them. Try...
Results 1 to 25 of 150
Page 1 of 6 1 2 3 4
All times are GMT -6. The time now is 10:32 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.