Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: rccheech

Page 1 of 40 1 2 3 4

Search: Search took 1.11 seconds.

  1. Replies
    2
    Views
    323

    +1 ^^^^^

    +1 ^^^^^
  2. Replies
    2
    Views
    183

    Check your brake linkage, it may be applying the...

    Check your brake linkage, it may be applying the brake.
  3. Replies
    14
    Views
    535

    The truggy has been doing great, its only seen...

    The truggy has been doing great, its only seen two races so far but drives like a dream. I went with an Adam Drake setup to start with other than the clutch setup and the shocks. I'm running all...
  4. Replies
    14
    Views
    535

    RE: Truggy rebuild

    Not yet....haha I've hit a brick wall for now. Still need an egine and pipe, servos and a transponder. Im actually too busy with racing right now to have time. This weekend is the Michigan State...
  5. RE: Cleaning bearings for bashers advice neeed....

    All you can reall do is hit them with a shot of wd40 or similar substance. You can try and pop the seals off and clean them, but its tough to do, usually if thier rough just replace them.
  6. Replies
    1
    Views
    315

    RE: Losi 8ight 2.0 Sic Month Check-up

    Defiantly a good rig. ;) keep up the cool videos too!!!
  7. Replies
    14
    Views
    535

    RE: Truggy rebuild

    Not too sure wbat clutch setup Ill run, I have 4 aluminium flywheels and 5 or 6 steel flywheel s all with different clutch setups, Ill just end up trying them out till I fing the one I like for it....
  8. Replies
    14
    Views
    535

    RE: Truggy rebuild

    Actually, I just run the vehicle as normal for a day, then change the fluids. that's it!!

    The aluminium inserts for the rear?...yes strongly recommend them....belive it or not shim the ring and...
  9. Replies
    14
    Views
    535

    RE: Truggy rebuild

    I think my diff setup is 5 7 3..... I honestly cannot remember, it might be 7 5 3...lol sheesh...I dont remember. But either way the diffs and ring and pinon need to be broke in because its all new...
  10. Replies
    14
    Views
    535

    RE: Truggy rebuild

    I know Losi is in the works for a new truggy. Im not exactly sure when but its possilbe I may find out more in August if I can get any hints from some friends that run for the team.

    The body...
  11. Replies
    14
    Views
    535

    RE: Truggy rebuild

    The front diff already had the hd diff case and the lightened outdrives, the center and rear were the factory ones and they were toast, so I went with the hd and light oudrives for those. I replaced...
  12. Replies
    14
    Views
    535

    RE: Truggy rebuild

    the top right picture is before I startedand the bottom right picture is after I finished
  13. Replies
    14
    Views
    535

    Truggy rebuild

    I know there is a truggy category but everyone that I talk to is in here.
    So here are some pics of the COMPLETE rebuild og the Losi truggy I got off eBay, man this thing was in bad shape, I...
  14. Replies
    21
    Views
    1,152

    RE: Let's talk thread lock (and shimming)

    Its not as hard to get out as you think if it does strip...one day it will...lol I promise. If you ever have trouble I could walk ya through it.
  15. Replies
    21
    Views
    1,152

    RE: Let's talk thread lock (and shimming)

    I always use a dab of blue threadlock. Worst case scenario I cut a slot in the screw with a dremel and a little heat from a micro torch and it come right out with a standard screwdriver...never been...
  16. Replies
    7
    Views
    552

    RE: Nitro Percentage

    Most engines are set to use up to 30% nitro content, anything higher and you want to add shims to prevent detonation. After about 30% nitro, you will not notice any difference on power, even the...
  17. Replies
    43
    Views
    1,223

    RE: Buggy pics thread!

    Few shots...
  18. Replies
    26
    Views
    882

    RE: can't go full throttle

    Not necessarily, if you have an air leak the engine will ilde higer because of it starving for fuel, it will sound different too at idle and be unstable, unless the idle stop is not adjusted...
  19. Replies
    26
    Views
    882

    RE: can't go full throttle

    If it's a slide carb it cant pull too far and start to close. What type of fuel are you running?? It is possible the front bearing is leaking when full throttle is applied and its sucking alot of...
  20. Replies
    26
    Views
    882

    RE: can't go full throttle

    Is the engine a rotary carb?? Or a slide carb??
  21. Replies
    8
    Views
    310

    RE: Outdrive wear

    No different to maintain, just stronger and will not wear the pin through the case.
  22. Replies
    8
    Views
    310

    RE: Outdrive wear

    Smart diffs just burn up....especially in a truggy, as stated above stay away from them, if anything the hd diff cases are the way to go.
  23. Replies
    8
    Views
    310

    RE: Outdrive wear

    Yes, anything to shave off rotating mass to gain spool up and faster acceleration. The Losi 3.0 comes with all of that, and alot more tuning options, thats one of the reasons they are at the price...
  24. Replies
    43
    Views
    1,715

    RE: Looking to get into racing nitros

    You'll be happy with the p5, for the price, it's a hell of an engine!!
  25. Replies
    26
    Views
    882

    RE: can't go full throttle

    Does it die abruptly, or does it bog down then die?? Have you changed your glowplug?
Results 1 to 25 of 1000
Page 1 of 40 1 2 3 4
All times are GMT -6. The time now is 12:13 AM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.