Search: Posts Made By: w8ye
Showing results 1 to 25 of 500
Search took 0.67 seconds.
Forum: Gas Engines 12-27-2017, 10:40 AM
Replies: 13
Views: 292
Posted By w8ye
People put 15cc four strokes in them

People put 15cc four strokes in them
Forum: Gas Engines 12-23-2017, 06:32 PM
Replies: 1
Views: 238
Posted By w8ye
Frank V. Ponteri of Maryville, TN and the AMA ...

Frank V. Ponteri of Maryville, TN and the AMA Passed away on Aprill 8, 2013
Forum: Gas Engines 12-15-2017, 03:23 PM
Replies: 3
Views: 266
Posted By w8ye
Regulator diaphragm in the carb may have gone...

Regulator diaphragm in the carb may have gone stiff?
Forum: Gas Engines 12-01-2017, 10:47 AM
Replies: 4
Views: 213
Posted By w8ye
.5mm or .020" but many people run them at...

.5mm or .020" but many people run them at .025"
Forum: Gas Engines 11-27-2017, 07:44 AM
Replies: 4
Views: 206
Posted By w8ye
Get a new fuel inlet and install it in the direct...

Get a new fuel inlet and install it in the direct you want.

Pull the old one out and push the new one in.

You can not turn them as they will break or collapse.

They are available from hobby...
Forum: Gas Engines 11-20-2017, 03:21 PM
Replies: 4
Views: 246
Posted By w8ye
The engine is a NGH 38 2245835

The engine is a NGH 38

2245835
Forum: Gas Engines 11-19-2017, 10:22 AM
Replies: 4
Views: 246
Posted By w8ye
Typically when a model four stroke drops a valve,...

Typically when a model four stroke drops a valve, It also bends all the mechanism. In the long run, it requires a new head assembly.
Forum: Gas Engines 11-12-2017, 11:10 AM
Replies: 10
Views: 371
Posted By w8ye
The mag has to be far enough from the flywheel so...

The mag has to be far enough from the flywheel so it doesn't hit.
Forum: Gas Engines 11-10-2017, 10:00 PM
Replies: 71
Views: 4,227
Posted By w8ye
Send the degree wheel to Tower for checking the...

Send the degree wheel to Tower for checking the timing by turning the engine backwards and claiming its 42 degrees and putting it in all their DLE manuals
Forum: Gas Engines 11-08-2017, 05:54 AM
Replies: 4
Views: 386
Posted By w8ye
It doesen't help vibration at all

It doesen't help vibration at all
Forum: Gas Engines 11-08-2017, 05:53 AM
Replies: 3
Views: 235
Posted By w8ye
These are diesel engines

These are diesel engines
Forum: Gas Engines 11-08-2017, 05:51 AM
Replies: 1,807
Views: 226,232
Posted By w8ye
+1

+1
Forum: Gas Engines 10-31-2017, 10:19 PM
Replies: 3
Views: 344
Posted By w8ye
Gale, Johnson, and Evinrude are all the same...

Gale, Johnson, and Evinrude are all the same company. Gale is Canadian.

This engine is water cooled and was made for many years
Forum: Gas Engines 10-20-2017, 05:10 AM
Replies: 11
Views: 396
Posted By w8ye
That's the vent for the regulator in the carb

That's the vent for the regulator in the carb
Forum: Gas Engines 10-03-2017, 10:41 AM
Replies: 11
Views: 435
Posted By w8ye
Typically, an engine with a bad reed will "pop"...

Typically, an engine with a bad reed will "pop" when trying to start but never run or hit more than just the one pop at a time.
Forum: Gas Engines 09-23-2017, 03:29 AM
Replies: 21
Views: 527
Posted By w8ye
The engines seem to run a little better at .025"...

The engines seem to run a little better at .025" rather than .020". So if you error on trying to achieve .022" -- go slightly large. Though too wide on the gap and the spark my miss fire?
Forum: Gas Engines 07-28-2017, 10:45 AM
Replies: 5
Views: 320
Posted By w8ye
No! The 11 & 21 are not like Walbros at all ...

No!
The 11 & 21 are not like Walbros at all
The 33 is actually a Walbro but is proprietary to Saito and you can only get them from Saito.
Forum: Gas Engines 07-18-2017, 07:10 PM
Replies: 4
Views: 373
Posted By w8ye
looks like an old Quadra 100 from the 80's? ...

looks like an old Quadra 100 from the 80's?

But the 2.6 is confusing?

Bennett was big on Quadras

The BME's and Brisson's had CD ignition
Forum: Gas Engines 07-17-2017, 01:44 PM
Replies: 3
Views: 246
Posted By w8ye
Why not set it up on a stand and try it out? I...

Why not set it up on a stand and try it out? I doubt two years was enough for the carburetor metering diaphragm to go bad?
Forum: Car Nitro & Gas Engines 06-30-2017, 02:40 AM
Replies: 2
Views: 345
Posted By w8ye
You are in the wrong forum with this question?...

You are in the wrong forum with this question? You need to go to nitro cars . . .
Forum: Gas Engines 06-23-2017, 01:53 PM
Replies: 7
Views: 320
Posted By w8ye
.010" or .25mm

.010" or .25mm
Forum: Gas Engines 06-23-2017, 12:56 PM
Replies: 7
Views: 320
Posted By w8ye
look in the parts list? I think there are shims ...

look in the parts list? I think there are shims that can be used to take up end play?
Forum: Gas Engines 05-27-2017, 05:40 PM
Replies: 15
Views: 353
Posted By w8ye
Mine is steel

Mine is steel
Forum: Gas Engines 05-26-2017, 06:23 PM
Replies: 15
Views: 353
Posted By w8ye
Without measuring with a caliper it is 3mm thick....

Without measuring with a caliper it is 3mm thick.

It will bend in a crash but you can remove/straighten it.
Forum: Gas Engines 05-26-2017, 03:57 AM
Replies: 2
Views: 266
Posted By w8ye
Sounds as though there's a lot of vibration? ...

Sounds as though there's a lot of vibration?

I enjoyed watching though.
Showing results 1 to 25 of 500



Forum Jump


All times are GMT -8. The time now is 06:04 PM.