Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: hfenn

Page 1 of 38 1 2 3 4

Search: Search took 0.24 seconds.

  1. Replies
    22
    Views
    367

    The dihedral for this airplane is two inches...

    The dihedral for this airplane is two inches total. I blocked up each panel 1" and sanded the root flush. Then I kept one panel on the board and propped the other up 2" and glued them together. ...
  2. Replies
    22
    Views
    367

    The rear sheeting can be glued on now. The bottom...

    The rear sheeting can be glued on now. The bottom wings need slots for the wing struts. It's easier to cut them now. Be careful gluing the sheet on so that the slot is next to the rib. Carve and sand...
  3. Replies
    22
    Views
    367

    Glue the tapered stock to the front of the 1/8"...

    Glue the tapered stock to the front of the 1/8" leading edge stock. Pin to the board and then lay down a 3/4" jig stick in the position drawn on the plan. Install the R2 ribs. The top and bottom...
  4. Replies
    22
    Views
    367

    All that remains for the fuselage is to install...

    All that remains for the fuselage is to install the firewall and bottom sheeting. The bottom sheeting goes on after the lower wing, so I'll leave that for later. Get the wing parts organized to...
  5. Replies
    22
    Views
    367

    After prepping the rudder assembly and fin, I cut...

    After prepping the rudder assembly and fin, I cut slots in the top deck sheeting for the dorsal part of the fin and glued the fin in place.
    20131232013124
  6. Replies
    22
    Views
    367

    The next thing I need to do is modify the...

    The next thing I need to do is modify the vertical tail parts to match the plan. Some of the first builders felt like the plane needed a little more rudder authority.
    2012607
  7. Replies
    22
    Views
    367

    The headrest assembly can be done now. I hope the...

    The headrest assembly can be done now. I hope the photos explain the process.
    201260420126052012606
  8. Replies
    22
    Views
    367

    Prepare to assemble the front upper deck blocks....

    Prepare to assemble the front upper deck blocks. It is made from the 3/16" X 3/8" balsa stick and the laser cut center piece. Cut the laser cut piece so that you remove the area that is taken up by...
  9. Replies
    22
    Views
    367

    Glue on the top rear deck sheeting. Trim and sand...

    Glue on the top rear deck sheeting. Trim and sand it to shape.
    20125952012596
  10. Replies
    22
    Views
    367

    I next glued on the horizontal stab making sure...

    I next glued on the horizontal stab making sure it on the fuselage center line and perpendicular to the cabane.
    2011958
  11. Replies
    22
    Views
    367

    Prepare the center cabane and 3/8" X 3/32" spruce...

    Prepare the center cabane and 3/8" X 3/32" spruce cabane leading edge re-inforcement. Then glue it in making sure it is on the center line and vertical. I used 5 minute epoxy....
  12. Replies
    22
    Views
    367

    I next glued the tail end over the plan view to...

    I next glued the tail end over the plan view to keep the side straight. Then I glued in F 4, 5 and 6. When sure all was straight and square, I finished gluing the formers to the left side with thin...
  13. Replies
    22
    Views
    367

    I have F-1 offset to build in right thrust as...

    I have F-1 offset to build in right thrust as called for in the plan.
    2011672
  14. Replies
    22
    Views
    367

    Formers F-1,2,3 and the panel are the same width,...

    Formers F-1,2,3 and the panel are the same width, so I began the fuselage join by tack gluing the left side and then checking to be sure everything was in alignment.
    2011671
  15. Replies
    22
    Views
    367

    Nah, I'll do it the hard way. I have to now.

    Nah, I'll do it the hard way. I have to now.
  16. Replies
    22
    Views
    367

    I'm trimming my doubler strips from the edges of...

    I'm trimming my doubler strips from the edges of the laser cut sheets. Next, install the strips, prepare the fuselage formers and cockpit floor from the 5/8" X 1/16" strips. There were no laser cut...
  17. Replies
    22
    Views
    367

    Mark the fuselage sides for the bulkheads. This...

    Mark the fuselage sides for the bulkheads. This will also give lines to guide the installation of the side stiffeners. Be sure to make a right and left!
    2011024
  18. Replies
    22
    Views
    367

    Here I've separated the parts by airframe part. ...

    Here I've separated the parts by airframe part.
    2011020
  19. Replies
    22
    Views
    367

    Select Hobbies SkiniWag build thread

    A Select Hobbies SkiniWag rode home with me from SMALL. Thanks Steve A (skaliwag)! It comes in a poly bag. Here are the contents. I broke a few parts in transport. That's one of the reasons they make...
  20. Replies
    62
    Views
    1,239

    I drive 12 hours to this event nearly every year...

    I drive 12 hours to this event nearly every year (too bad you can't make the 4 hour drive to find out for yourself). I see friends I made at my first one in 1999. I also miss some of the old f@rts...
  21. Replies
    62
    Views
    1,239

    It is. Use way-points. On the way down stop in...

    It is. Use way-points. On the way down stop in Dayton and see the AF museum at Wright-Patterson. On the way back, spend a day in Nashville (you may decide to move down here if you do though). I...
  22. Replies
    62
    Views
    1,239

    I don't have my list finalized, but I'll have at...

    I don't have my list finalized, but I'll have at least one control line, two glow r/c, two free flight glow, some rubber free flight, some R/C electrics including multirotors, and a rocket (Big...
  23. Replies
    62
    Views
    1,239

    I've seen how you can pack a vehicle. It will be...

    I've seen how you can pack a vehicle. It will be awesome!
  24. Replies
    62
    Views
    1,239

    Planning to be there. Hollis

    Planning to be there. Hollis
  25. I'll have some new 2S and 3S 5000mAh LiPo's for...

    I'll have some new 2S and 3S 5000mAh LiPo's for sale.
Results 1 to 25 of 947
Page 1 of 38 1 2 3 4
All times are GMT -6. The time now is 02:35 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.