Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: w8ye

Page 1 of 40 1 2 3 4

Search: Search took 1.10 seconds.

  1. Replies
    1
    Views
    86

    Four stroke gas or glow engines are not sensitive...

    Four stroke gas or glow engines are not sensitive to muffler back pressure like a two stroke engine.

    The gas version does not use muffler pressure at all.
  2. Replies
    1
    Views
    105

    If you want to turn the ignition off/on with your...

    If you want to turn the ignition off/on with your transmitter it is OK. But I would still have a manual slide switch in the ignition circuit too.
  3. Replies
    17
    Views
    543

    Next week the metering valve diaphragm will be...

    Next week the metering valve diaphragm will be stiff again.
  4. Replies
    24
    Views
    576

    The 65cc are Stihl MS390 replacement engines on...

    The 65cc are Stihl MS390 replacement engines on Ebay

    look for 49mm bore?

    Some listings are 46mm bore = 59cc
  5. Replies
    24
    Views
    576

    These are Stihl Clamshell engine designs that are...

    These are Stihl Clamshell engine designs that are available < $100 new as short blocks. They are made in China but run excellent.

    65cc
    ...
  6. Replies
    24
    Views
    496

    The old C&H shielded cap was a Mercedes Benz...

    The old C&H shielded cap was a Mercedes Benz part.

    I run a Homelite 30 with unshielded wire and never had a glitch with the old radio system.

    C&H had a plug wire with a braid shield underneath...
  7. Replies
    24
    Views
    496

    Measure the old wire but I think it is 5mm? ...

    Measure the old wire but I think it is 5mm?

    http://www.hlsproparts.com/Spark-plug-wire-by-the-foot-p/h45001.htm

    http://www.hlsproparts.com/Spark-plug-wire-with-cap-p/h45000.htm
    ...
  8. Thread: Sachs 4.2 Engine

    by w8ye
    Replies
    21
    Views
    1,978

    "Most people tune the high speed first but...

    "Most people tune the high speed first but actually the low speed controls the basics of the high end...opposite of a nitro."

    That's because the low speed has outlets downstream of the venturi...
  9. Replies
    7
    Views
    252

    The old G38's had a skinny steel prop hub instead...

    The old G38's had a skinny steel prop hub instead of a fat aluminum one.

    Either old or new, they turn a 18-10 about the same rpm.
  10. AFAIK The G-26 with the four bolt cylinder flange...

    AFAIK The G-26 with the four bolt cylinder flange is the one that can be converted.

    A two bolt G-23 cannot
  11. Replies
    7
    Views
    252

    Yes on the side

    Yes on the side
  12. Replies
    7
    Views
    252

    The current carb is a WT-338 and it uses a Walbro...

    The current carb is a WT-338 and it uses a Walbro K20-WT complete repair kit.

    The old ones had a WTA-6A carb and it used a Walbro K20-WTA complete repair kit


    I don't think the WTA-6A had a...
  13. Replies
    87
    Views
    9,726

    FYI The OP was from Kunming Yunnan PR China ...

    FYI

    The OP was from Kunming Yunnan PR China

    DL Engines list their address as Miyang Industry Zone, Mile Industry Area, Mile City, Honghe Prefecture, Yunnan Province, PR China

    Mile and...
  14. Replies
    19
    Views
    534

    35RA inverted

    35RA inverted
  15. Replies
    85
    Views
    6,459

    Sticky: Any intermittent action of the sensor will cause...

    Any intermittent action of the sensor will cause a spark. For example, The sensor "makes" or conducts as the magnet first approaches the sensor but while the magnet is fully under the sensor, the...
  16. Replies
    22
    Views
    1,122

    You best just keep it. At least you have it? Send...

    You best just keep it. At least you have it? Send it back and you may have nothing?
  17. K24-hda

    K24-hda
  18. Thread: Saito FG-60R3

    by w8ye
    Replies
    394
    Views
    27,214

    But are the Rimfires almost twice as good? For...

    But are the Rimfires almost twice as good? For that is the difference in price.
  19. Replies
    8
    Views
    362

    You can. The needle will be too lean on the...

    You can.

    The needle will be too lean on the DA50 if they were adjusted for a 40 or 50:1 ratio

    Some people will claim that you will get a lot of carbon on the piston. Haven't seen the extra...
  20. The rusty bearings are a different situation from...

    The rusty bearings are a different situation from the wrist pin retainer coming out.

    With a new piston and sleeve plus new bearings and wrist pin retainers, you will be good as new.

    The head...
  21. Replies
    78
    Views
    2,491

    Where I fly there's probably more DA's than any...

    Where I fly there's probably more DA's than any other one brand. I've seen several have problems. They were all sent back to DA and the owners were happy.

    Seen a few DL & DLE problems too. Either...
  22. Replies
    78
    Views
    2,491

    The DA customer service is good enough that few...

    The DA customer service is good enough that few people repair their own DA's and you see few spare parts for sale on the Internet.
  23. age

    age
  24. Replies
    30,977
    Views
    1,849,570

    Saw a guy at work that had one of those LeFevre...

    Saw a guy at work that had one of those LeFevre 12ga that came unraveled. Looked like a spring. He loaded his own shells and I figure he used to much of the wrong powder?

    I worked in a seamless...
  25. Replies
    4
    Views
    164

    TOWER still has just a few parts but not the ones...

    TOWER still has just a few parts but not the ones you are looking for.

    You will just have to be resourceful? Use sand paper for the prop bushing.

    Figure out the thread size on your crankshaft...
Results 1 to 25 of 1000
Page 1 of 40 1 2 3 4
RCU Reviews
All times are GMT -6. The time now is 09:22 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.