Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: eaticus

Page 1 of 2 1 2

Search: Search took 1.47 seconds.

  1. RE: $1,000.00 bounty offered to fix COMP ARF A4 steering

    Did u ever fix the problem?
  2. RE: $1,000.00 bounty offered to fix COMP ARF A4 steering

    Let me have a go at it...

    The master cylinder and slave cylinder must match in size (bore and shaft dia); just purchase two identical cylinders. see attached illustration.

    Installed the...
  3. Replies
    18
    Views
    1,360

    RE: CG'ing A Large Jet

    Here is another method similar to Mr. Gladwins method.

    Remember that if you have to add weight to achieve balance, it would be an interative process.
  4. RE: George Miller F-4 Build - also, welcome George!

    Hi George,

    I will take that advise to heart! I really appreciate it. My opinion on weight is the same as you.

    My plan is to power it with either 90mm or 120mm EDF units.

    I thought...
  5. RE: George Miller F-4 Build - also, welcome George!

    Oh... sign me up...

    Question for Mr. Miller,
    I recently acquired a set of your A-10 plans. Do you have any advise that you could give? I would appreciate it very much...

    Dave
  6. Replies
    1,555
    Views
    122,767

    RE: Carl Goldberg Ultimate 10-300 Brotherhood.

    Signing on! Had two of 'em! Working on #3. I have had numerous ultimate bipe in numerous sizes ranging from Flat foamies to 50cc. Goldberg Ultimate is by far my favorite ones!

    I'll take #18 ...
  7. RE: Trex450SEv2 1st HOVER...THROTTLE TWITCHING!?!?!?!

    Hi,
    I had this exact problem. I thought was the ESC also. I tried several ESCs. Ranging from cheapo to CC Phx45. It all did the same thing. I finally swapped the cheapo receiver for the JR PCM...
  8. A question that's been bothering me for a while...

    Not related but...

    Why does a set screw also called "Grub Screw"? Where did "Grub" term come from? Just curious... :)

    thanks!
  9. Replies
    110
    Views
    10,481

    RE: Mid-Air at Markham Park

    All the mid-air that I have ever witnessed have always have been just TWO (2) airplanes in the air.

    The remedy to the problem: get at least three (3) airplanes in the air.
  10. Replies
    2
    Views
    599

    RE: VioJett instructions

    I was cleaning my basement and found them. I've scanned it as pdf format. Let me have you e-mail address and I'll sent them to ya!

    Dave
  11. Replies
    1
    Views
    401

    RE: KAMDAX fan unit

    You may want to consider electric (brushless motor) setup. It will easily outperform the glow-counterpart.

    http://www.ejf.com/index.php?main_page=product_info&cPath=82_79&products_id=195

    ...
  12. Replies
    3,996
    Views
    503,283

    RE: Nitro models pusher Bobcat?

    Now I am even more confused... (it doesn't take much... :eek: )

    The retract is approximately 1" tall, with hole for 3/16" wire. I wanted a softer gear and went with 5/16" wire. The brass tube...
  13. Replies
    3,996
    Views
    503,283

    RE: Nitro models pusher Bobcat?

    hapyjac2,
    I believe that they are the older 300 series. They have been collecting dust in the shop for a long time (at least 7 years). I looked up retracts.com and unable to find exact match.
    ...
  14. Replies
    3,996
    Views
    503,283

    RE: Nitro models pusher Bobcat?

    Here is a pic of my retract installation. I am really, really, really slow at building... [:-]

    Dave
  15. Replies
    3,996
    Views
    503,283

    RE: Nitro models pusher Bobcat?

    Topper,
    I have a set of low height (1" height) Spring air that has been laying around the workshop for a little while. It fits pretty nice in the wings. My camara battery died last night and...
  16. Replies
    3,996
    Views
    503,283

    RE: Nitro models pusher Bobcat?

    Awesome Video! Thank you for sharing :)



    Dave
  17. Replies
    3,996
    Views
    503,283

    RE: Nitro models pusher Bobcat?

    Mark,
    Have you been able try other prop/motor setups? I am thinking to build it electric too!

    I've been working on installing retracts. Will post pics later.

    Thanks!

    Dave
  18. Replies
    3,996
    Views
    503,283

    RE: Nitro models pusher Bobcat?

    SJN,
    Good to know that the mfg corrected the instruction book!

    Dave
  19. Replies
    3,996
    Views
    503,283

    RE: Nitro models pusher Bobcat?

    topper5,

    Congratulations!

    Thank you for being the First!
    This is great encouragement for the rest of us.

    Dave
  20. Replies
    3,996
    Views
    503,283

    RE: Nitro models pusher Bobcat?

    I am not sure if this is appearant. I think the CG location as indicated (6.9 inches) may assume that the plane is balanced with an empty tank. (My JHH Mirage has tank aft the Aero Center and the...
  21. Replies
    3,996
    Views
    503,283

    RE: Nitro models pusher Bobcat?

    Hi,
    I had a short circuit in my brain, went crazy, and bought 2. I'll part with one if you have figure out how to ship the airplane. It should be here about a week...

    Dave
  22. Replies
    3,996
    Views
    503,283

    RE: Nitro models pusher Bobcat?

    Wow... looks like a great fit for MW44 conversion... or EDF conversion

    website: www.nitroplanes.com
  23. Replies
    7
    Views
    962

    RE: Cen .46 engine

    Do you guys have the link or issue number for that test?

    Thanks!

    Dave
  24. Thread: Tuned pipe

    by eaticus
    Replies
    5
    Views
    631

    RE: Tuned pipe

    Try:

    http://www.jdenterprise.net/

    Dave
  25. Replies
    7
    Views
    962

    RE: Cen .46 engine

    Thanks!

    Has anyone retrofit the cen engine into other vehicles and see significant power improvements?

    Thank you all in advance!

    Dave
Results 1 to 25 of 36
Page 1 of 2 1 2
All times are GMT -6. The time now is 12:47 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.