Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: RCLT40

Page 1 of 5 1 2 3 4

Search: Search took 1.28 seconds.

  1. Replies
    6
    Views
    182

    I checked the prop and it is a GWS 5x3. And it's...

    I checked the prop and it is a GWS 5x3. And it's only long on one side so something isn't quite correct. I installed the motor mount and lined it up with the center line of the wing. (where the two...
  2. Replies
    6
    Views
    182

    It's. The prop that came in the box. Im wondering...

    It's. The prop that came in the box. Im wondering if i didnt mount the motor correctly?.
    when i get home i'll check the prop size just to make sure.
  3. Replies
    6
    Views
    182

    Nitroplanes mini pop wing

    Just finished building my mini pop wing and I find that the prop supplied with the kit is too big. The tips of the prop hits the pop wing. So my question is do I trim the prop or cut back the wing...
  4. Replies
    0
    Views
    135

    West Coast Mini Festival

    Mark this event on your calender because it's a great event. Delta Valley Modlers anual West Coast Mini Festival is a great even well attended and we generally get a good crow of spectators as well....
  5. RE: Are you new to QUAD copters? And need advice stop in and ask me,

    I just purchased a CR-230 MWC quadcopter for Xheli. The only thing I need to do to get it flying is configure it. And that's were I'm stuck.
    It came with a manual but it's only minimal help. I'm...
  6. Replies
    2
    Views
    613

    RE: Swap meet vapor purchase

    That's what I found out when I emailed Horizon Hobby. I have there 800 number I hope to call to get more help
  7. Replies
    2
    Views
    613

    Swap meet vapor purchase

    Today ki picked up a vapor at the RCContry swap meet. I got it for a really good price but after getting it home I find I can't get it to bind to my DX7. So my first question is how do I know I...
  8. Replies
    4
    Views
    614

    RE: Hobby People 4120/05 ESC

    Bummer. I have already purchased the other one. But thanks for the insite. I'll read up on it.
  9. Replies
    4
    Views
    614

    RE: Hobby People 4120/05 ESC

    Thanks. I'll check it out.
  10. Replies
    4
    Views
    614

    Hobby People 4120/05 ESC

    I have a question. I have a 4120/05 brushless motor that i need a ESC for. I know that it needs to be a 70 amp because the motor max amp is 65. The tech sheet for the motor says that the ESC needs a...
  11. Replies
    2
    Views
    442

    RE: Turnigy Accucell-8150

    that's a good idea. I did try and use my pickup battery but never checked the voltage on that battery.
    I'll test that out this week end hopefully.
  12. Replies
    2
    Views
    442

    Turnigy Accucell-8150

    A few months back I purchased at Accell 8150 from Hobby King. I needed a larger charger for the 6s I had purchased from H.K.
    I find that I can use the charger fine on my 20amp power supply on my...
  13. AMA 75th Anniversary & West Cost Mini-festival

    Are you planning on attending the West Cost Mini-festival this September?
    It start Thrursday September 1st. Ending Sunday September 4th.
    We have plenty of RV parking and a full size landing strip...
  14. West Coast Mini-Festival & AMA's 75th anniversary celebration

    Delta Valley Modelers is hosting the West Coast Mini-Festival & celebration for AMA's 75yh anniversary.
    We are hoping that a larg number of pilots show up so the even will be successful.
    Stop...
  15. Replies
    9
    Views
    708

    RE: Turnigy Battery & Charger

    Thanks, I think I'll go ahead and take another voltage reading with a better metter before I proceed with dropping the voltage of a singel cell.
  16. Replies
    9
    Views
    708

    RE: Turnigy Battery & Charger

    I only have a radio shack type volt meeter and it shows each cell as just under 5 volts.
    The watt meter doesn't have the correct connector to measure the voltage from the balancing plug.
    I'll...
  17. Replies
    9
    Views
    708

    RE: Turnigy Battery & Charger

    I have have check the pack with two meters. The one that connects to the balancing plug and my watt meter that plug into the charging leads.
    The watt meter reads 25.12 volts. If I take the...
  18. Replies
    9
    Views
    708

    RE: Turnigy Battery & Charger

    Guver;
    In reference to the voltage I have a meter that I plug into the balance plug so I'm guessing that the voltage reading is correct.
    So shall I put the battery on the discharge fuction and...
  19. Replies
    9
    Views
    708

    Turnigy Battery & Charger

    I recently received at Turnigy Accuell-8150 battery charger and Turnigy s6 battery for my newest project.
    I partly charge the batter last week and put it back on the charger just tonight. After it...
  20. Replies
    465
    Views
    25,406

    RE: Vehicle Naming Contest (NEW) Posted May 5

    Rat-rod
  21. Replies
    465
    Views
    25,406

    RE: Vehicle Naming Contest (NEW) Posted May 5

    Zorro..
  22. Replies
    0
    Views
    265

    WarBird Flyin

    This Saturday we are hosting a Warbird event.
    Fixed pitch or rotory if it's a warbird it's welcome.
    Just $10.00 to fly. Check our web site for more details

    ...
  23. Replies
    0
    Views
    421

    War Bird Fun Fly

    Delta Valley Modelers
    Wants you to join them at Kingdon field in Lodi, Ca for our Annual War Birds fun fly.
    Bring your friends and enjoy the food, fun and raffle.
    As last year the event is...
  24. Replies
    4
    Views
    321

    RE: Spectrum Helio Transmitter

    thanks for you sugestions.
    I may stay will the smooth stick. I'm just worried I might bump it at the wrong time.
  25. Replies
    4
    Views
    321

    Spectrum Helio Transmitter

    I have a Spectrum Helio transmitter that I'm using to fly fixed wing as well.
    Is there a way to turn on the ratchet effect in the throttle?


    Thanks.
Results 1 to 25 of 119
Page 1 of 5 1 2 3 4
All times are GMT -6. The time now is 06:36 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.