Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: Bax

Page 1 of 40 1 2 3 4

Search: Search took 1.51 seconds.

  1. Replies
    1
    Views
    25

    The normal sequence is: 1) Remove cylinder ...

    The normal sequence is: 1) Remove cylinder head; 2) Remove rear cover; 3) Slide cylinder liner up, out of the case; 4) Move piston and rod assembly aft to take the rod off of the crank pin. The...
  2. Standard shipping is $9.99 on all non-warranty...

    Standard shipping is $9.99 on all non-warranty work.
  3. A gyro-only maintenance check is $18.50, but...

    A gyro-only maintenance check is $18.50, but does not include any repairs.
  4. Replies
    1
    Views
    48

    Some of those specs were written and published...

    Some of those specs were written and published before the transmitter was actually released.

    You can have up to 10 characters for both the model name and the user name.

    You can adjust how...
  5. First off, you're not powering the gyro...

    First off, you're not powering the gyro correctly. It is rated for 6.0V Maximum, but will be better off at a lower voltage. It's recommended to regulate it at 5.2V. This could be causing the gyro...
  6. Replies
    1
    Views
    55

    That's how Futaba bills it.

    That's how Futaba bills it.
  7. Replies
    2
    Views
    54

    Other than the case, supercharger, crankshaft,...

    Other than the case, supercharger, crankshaft, rear bearing, crankcase gasket set and intake manifold, the parts are all the same as for the FS-120 Surpass II and FS-120 Surpass-E
  8. Thread: Bearing shields

    by Bax
    Replies
    3
    Views
    50

    Omega fuel is good.

    Omega fuel is good.
  9. Thread: Bearing shields

    by Bax
    Replies
    3
    Views
    50

    You can remove them, if you wish. The "safest"...

    You can remove them, if you wish. The "safest" way to remove the shields would be to carefully pry it out. You need something with a point, like an icepick, and then work it under the groove that...
  10. First off, what are you calling "failsafe"? In...

    First off, what are you calling "failsafe"? In most cases, a failsafe event happens when a signal is lost between the transmitter and receiver. The receiver then sends the different control...
  11. We cannot help you program the Phantom 2 system....

    We cannot help you program the Phantom 2 system. We don't work with that manufacturer's equipment. With Futaba equipment, failsafe is set in the transmitter, and you just do it like it's said on...
  12. Thread: Futaba 9CA

    by Bax
    Replies
    6
    Views
    814

    Please check which channel(s) the flaps are...

    Please check which channel(s) the flaps are connected to. If you're using two channels and a mixer, check the direction of the mixer. Check the servos. Usually, flap servos have the pushrods...
  13. Replies
    3
    Views
    129

    First off, we can see that your receiver antennas...

    First off, we can see that your receiver antennas are not mounted correctly. Both are pointing to the side, essentially parallel. They should be at 90-degrees to each other: one forward and one to...
  14. Replies
    7
    Views
    166

    The SuperTigre G-2300 is built in the G20 design...

    The SuperTigre G-2300 is built in the G20 design series of engines. There never was a 2000-size engine in the G-series of engines.

    Years ago, there were engines such as the G20/.15 and the...
  15. Replies
    2
    Views
    89

    Yes, you can easily use those sensors. The...

    Yes, you can easily use those sensors. The R7008SB receiver it comes with will handle all your needs.
  16. Replies
    1
    Views
    77

    The Futaba BLS173SV and BLS173SVi are the same...

    The Futaba BLS173SV and BLS173SVi are the same servo, but t he BLS173SVi does not come with a lead attached. It has a micro connector on it and you then use any one of these leads to connect it to a...
  17. Replies
    1
    Views
    61

    According to the transmitter's instruction...

    According to the transmitter's instruction manual, you'll need this part:

    FUTM4420 MDTC TRNR CORD MICRO/ROUND PLG US$14.99

    These parts can be ordered through any hobby retailer who sells...
  18. Replies
    1
    Views
    95

    We think the Robbe telemetry box might work...

    We think the Robbe telemetry box might work because Robbe says that it will accept signals from any Futaba FASSTest receiver. However, we'd not know why you'd want to use it with an 18MZ, since the...
  19. Replies
    2
    Views
    89

    The Throttle Cut function only works on the...

    The Throttle Cut function only works on the throttle function, so you could name both throttle channels as "Throttle". Unfortunately, this will then prevent you from using mixers to control the...
  20. Replies
    4
    Views
    167

    As far as your opinion of how you Futaba should...

    As far as your opinion of how you Futaba should have programmed the 18MZ, we don't have an answer. We don't have information on how it was done by Futaba, in Japan. We are the support center for...
  21. Replies
    8
    Views
    165

    So it looks like the ESC cannot deliver the power...

    So it looks like the ESC cannot deliver the power needed to operate the full system and it overloads and shuts down. Good on you for finding the difficulty!
  22. Replies
    64
    Views
    1,950

    The alcohol used in automobile gasoline is...

    The alcohol used in automobile gasoline is Ethanol, made mainly from corn. The alcohol used in model fuel is Methanol, derived from cracking petroleum. The price of one does not affect the price...
  23. Replies
    9
    Views
    272

    Please be aware that older AM systems may not be...

    Please be aware that older AM systems may not be legal. Please make sure it has the gold AMA sticker on it. The laws changed just before AM systems were phased out, and most AM systems had to be...
  24. Replies
    4
    Views
    167

    Nothing has been overlooked. To get 18 channels...

    Nothing has been overlooked. To get 18 channels in the 18MZ, room had to be made somewhere, so virtual channels went out. In the old 14MZ, you had four virtual channels, but only 14 actual...
  25. The easy way to check is just plug them together...

    The easy way to check is just plug them together and see! If the mode change is done "properly", then the channel order stays the same, but the sticks are different. With Futaba, the general setup...
Results 1 to 25 of 1000
Page 1 of 40 1 2 3 4
All times are GMT -6. The time now is 09:26 AM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.