Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Search:

Type: Posts; User: rernewe

Search: Search took 0.50 seconds.

  1. RE: I need the part number for the main rotor grip assembly for this CNC head

    thanks in advance for the help.
  2. I need the part number for the main rotor grip assembly for this CNC head

    Hi, I need the part number for the main rotor grip set for this rotor head (the one that includes all the bearings, thrust washers etc.. to put the head back together after changing the feathering...
  3. RE: XHeli CNC Upgrades - how good are they????

    I bought this one

    http://www.xheli.com/ebl400cnfiup.html

    turnedout to be a great deal, 2 sets of carbon fibre blades, CNC rotor head assembly(need to cut about 3mm off theshaft for it to fit...
  4. RE: instructions for changing the motor in my RC18T ?

    Hobbyking has a couple that are $15.95, go on the site and search for rc18t and it gives a list of parts that fit the car. I just ordered a 4200kv and 6200kv to try. I can send you the part numbers...
  5. RE: instructions for changing the motor in my RC18T ?

    yup, screaming fast, and the heat was so bad i pulled the motor before it fried itself, fun for a short time, i think it was running faster than 30mph
  6. RE: instructions for changing the motor in my RC18T ?

    I'm using a hobbywing 7800kv motor and a 25a esc. The motor was getting too hot to touch so i'm installing something a little slower, going to try a 4200 and 6200 and see how they work.
  7. RE: instructions for changing the motor in my RC18T ?

    thanks for the tip, i installed brushless and made sure the mesh was good, runs smooth and i can't believe how fast it is, i never expected these speeds from 1/18 scale.
  8. RE: instructions for changing the motor in my RC18T ?

    thanks, that helps, there is a plastic guard that had me thinking i had to take it apart, i'll remove it and follow your instructions.

    thanks again.
  9. instructions for changing the motor in my RC18T ?

    Does anyone have instructions or a video for changing the motor on these? I'm used to the larger 1/10 scale where you remove 2 screws and the pinionand the motor pops right out. I just bought a used...
  10. Replies
    2
    Views
    538

    RE: spektrum 2.4ghz radio system ????

    I put a DX3E in my Redcat Tornado, works great, Range is great, i've driven it down the street as far as i can see it clearly and never miss a beat. Came with a digital servo that gives better...
  11. Redcat Tornado EPX pro pinion gear part numbers are incorrect

    Hi I ordered the following pinion gears from my LHS for my Tornado EPX pro so i could try different gearing for speed and torque, none of them fit, can you explain this? your web site where i got all...
  12. Replies
    59
    Views
    14,177

    RE: *RedCat Racing Tornado EPX Thread*

    The response i got from Redcat was that the ESC is only good for 2s. The motor should be ok with 3s.
  13. Replies
    188
    Views
    13,227

    RE: 80+ MPH?! I don't think so...

    put the GPS on my Tornado EPX PRO brushless, stock with 2s lipo, got 52kmph (32mph) and it wasn't quite at full speed yet,
  14. Gearing ratios for the Tornado EPX pro brushless?

    Hi, i'm looking for the gearing values for the differential. There are some calculators on the web that will tell me what speeds to expect with different pinions, motors and batteries etc...but they...
  15. RE: Tornado EPX Pro steering servo, Analog or Digital?

    Yes, seems much smoother and more responsive when turning, i don't have much experience with this so i didn't realize how much better it would be than analog.
  16. RE: Tornado EPX Pro steering servo, Analog or Digital?

    Swapped out the servo for the digital one that came with my DX3E, no issues, slotted right in with the included hardware.
  17. Tornado EPX Pro steering servo, Analog or Digital?

    Is the the factory servo digital or analog? I have a digital servo i'd like to swap in but not if the factory one is already digital.

    thanks, couldn't find anything on the Redcat web site.
    ...
  18. Replies
    17
    Views
    1,469

    RE: Can anyone identify this plug?

    Sheograth, they are not mini EC3, check this site:

    http://www.supertigre.com/electric-power/adapters.html

    they are Supertigre connectors, i checked E-flite EC3 and they don't list anything...
  19. Replies
    17
    Views
    1,469

    RE: Can anyone identify this plug?

    that's right, EC3 are blue and are both connectors on the plug aremale or female depending on if they are battery or device, the red connectors they are asking about are the Super Tigre connectors...
  20. Replies
    17
    Views
    1,469

    RE: Can anyone identify this plug?

    they are thunder tiger or supertiger, i don't recall which but i checked at my LHS after i got them on several batteries i purchased from HobbyKing. I replaced them with the EC3 connectors which are...
  21. Tornado EPX pro Electric motor and ESC ??

    Can anyone tell me if i can upgrade the ESC to use 3s lipos without upgrading the motor or do i need a new motor as well?

    thanks.
    </p>
  22. RE: replacement parts for my CNC rotor head

    Thank you very much!!
  23. which feathering shaft do i need for the blade 400 rotorhead i just bought???

    i purchased this combo for my Blade 400:
    <font color="#00265e">http://www.xheli.com/ebl400cnfiup.html</font>

    which feathering shaftdo i need as a replacement?

    thanks!!
  24. replacement parts for my CNC rotor head

    i purchased the upgrade combo for my Blade 400:
    http://www.xheli.com/ebl400cnfiup.html



    how do i find the feathering shaft replacementsfor this unit?

    thanks!!
Results 1 to 24 of 24
All times are GMT -6. The time now is 04:42 PM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.